|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 741 Registered: May-06 | We will be down for 4 Hours into 2:00 Pm Pacfic For Fixes We are trying to Maintain are servers Futrue-Fta Has all Pansat Fixes as of 6-08-06 Please check back We will be back soon... |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 742 Registered: May-06 | For ALL Pansats.... Things you will need! 1.A computer with a com port! 2.The right cable to connect to your computer to your receiver! 3.The most recently LOADER 4.New pansat bin!.. 5.LNB setup and the right switch! 6.Sat Signal at 70 percent or higher! -------------------------------------------------------------------------------- ----- 1.Power down receiver and computer! 2.Connect receiver to computer and power both of them up! 3.Start up gtrom newest version and select the new bin file you wish to upload then click download wait until it is finished it will go to a 100 percent but it is not finish until it displays burn complete or finished! 4.Turn off power to receiver and computer and remove the cable from the receiver! 5.Install cable from the lnb and the cable from the tv and the plug it up and power up the receiver! 6.Using your remote hit menu and the parent control then ok in second pin enter 0000 and then ok! 7.Then set default key..EMU-ON then ok! 8.Go to Nagavision2 then ok and check 00 and 01 keys. Put in new keys if need then hit ok to save! 9.Now installation then ok antenna setup then ok make sure you have 110 and 119 and check to make sure the switch is set right for both on the diseqc setting! If 110 is on 1 and 119 is on 2, set diseqc the same way! 10.Now go to blind scan and hit ok! 11.When finished exit menu and watch tv! |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 743 Registered: May-06 | Here are a few tips if you are having difficulty flashing: loading a bin.. I would advise everyone to read a set up guide before flashing. But, since people have been having some problems, I have revised this to provide more detailed information. But this is not intended to be a substitute. 1. Make sure you use the proper serial cable for your receiver: Most Fortec and Pansat use a straight through cable with DB9 females on both ends. The Blackbird, Pansat 2700/3500 and some other receivers use null (crossover) cable, which crosses over pins 2 and 3. 2, With the power turned off, connect it to your computer and receiver using the serial connector. Use serial port #1 if you can. 3. If you do not have a working SERIAL port, you must install one or use a computer that has one. Usb ports do NOT usually work, except on rare ocassions with an adapter. 4. Use the appropriate loader. 5. Select the file. Make sure that it is the correct flash for your receiver. 6. Select the COM port your receiver is connected to. If you do not know, what it is try #1 first. 7. Enter the correct model name and number. Most Blackist updaters do Not require this. 8. Check off the correct function box. Your choices are boot, flash or channel list. To FLASH your receiver you would use FLASH. Most flashes do not require a separate boot; so do not load both separately. 9. Turn on the receiver power from the BACK switch. 10. As soon as you see the lights flash,very first light -- IMMEDIATELY press download. Timing is critical and many vary. 11. Wait until it COMPLETES and reboots. |
|
New member Username: Jez0757Tampa, Florida USA Post Number: 6 Registered: May-06 | Ola Eva, How can one tell if they have a "clone"? I have a Pansat 2700. I also have a Quantum 4700 in the box... have not used the Quantum. I have posted requests for info on the Quantum and NO ONE has responded...Have you ever heard of it? and if so...can the current bin be used on it??? Any info would be greatly appreciated. |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 748 Registered: May-06 | I dont have information about quantum receiver. So sorry. |
|
New member Username: SonyaPost Number: 10 Registered: Jun-06 | Eva! Do you have a fix for digiwav 7000. please help |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 749 Registered: May-06 | No, sorry. For Digiwave are still waiting. |
|
Silver Member Username: BoycePost Number: 246 Registered: Apr-06 | Eva what kind stb you have? |
|
New member Username: DishyPost Number: 2 Registered: May-06 | DishNet to Bev. I"m very new to the fta scene and need your expert knowledge on how to switch from DN to BEV. I've been getting DN channell on the pansat2700a. But I understand that ESPN is on BEV and I want to switch to BEV. I"M running on bin 148 currently. in addition to pointing my dish to a different sat. do I need to load any other bin or channel list to get BEV? thank you in advance for your assistance |
|
New member Username: AidynPost Number: 2 Registered: Jun-06 | Please Help Me with Pantec Ultra Where I can find the New Bin Many Thanks |
|
Bronze Member Username: VndpatelPost Number: 47 Registered: Mar-06 | eva where do u get the latest bin for pansat? |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 753 Registered: May-06 | Boyce Stb? |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 754 Registered: May-06 | dss***tester.com |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 755 Registered: May-06 | THis Bin is not totally safe for Ultra or Pantec Do you need read before. |
|
Silver Member Username: BoycePost Number: 248 Registered: Apr-06 | recevier |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 756 Registered: May-06 | Pansat 2700 |
|
New member Username: SolitoPost Number: 5 Registered: May-06 | Hola Eva, Please darling where is that clone safe bin for pensat 2500 ????? |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 762 Registered: May-06 | ITS not safe for Clone yet. Do you need wait a little. So sorry. |
|
New member Username: OrbitekcommPost Number: 3 Registered: Jun-06 | What is the most recent loader for pansat 2500? |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 764 Registered: May-06 | rich go to dss***tester.com for the last download, in pansat area. Lucky |
|
Bronze Member Username: VndpatelPost Number: 48 Registered: Mar-06 | so all pansats are working? |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 767 Registered: May-06 | yes |
|
New member Username: AerospeedPost Number: 1 Registered: Jun-06 | hey guys, i just flashed my pansat 2700A with the bin from dsstester(dot)com and there was no parental control or channel edit and also, after selecting a satellite with a 90+ quality and 85+ signal and doing a blind scan, no channels came up (not even english channels)....what may be wrong?...and yes i do know how to CORRECTLY flash a reciever and i have also read the forums and couldnt find anything relating to this problem. any help on what might be wrong or what i can do to fix this problem will be appreciated! |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 778 Registered: May-06 | Select a satellite, and try advanced scanning. Check autoroll of if you have that option and check in parental control key emu on. Lucky |
|
Bronze Member Username: NabilPost Number: 17 Registered: Jun-06 | i have the same problem like H. Patel........there is no second pin in the parental control menu!!! how could i enter the keys??? |
|
Bronze Member Username: Hawks134Post Number: 19 Registered: Jan-06 | In the loader, what do you type in bin file? |
|
Bronze Member Username: PoscorPost Number: 31 Registered: Feb-06 | click on bin file box double click on file you want to use |
|
New member Username: Jpatel83Post Number: 1 Registered: Jun-06 | I have a pansat 3500d, i need information on how to program the reciever. and what program you use to update the files onthe reciever thanks |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 801 Registered: May-06 | Pansat 3500 REprograming How to Load and Save Files to the Pansat 3500S 3500 - THE SD/MMC WAY: Insert virgin SD/MMC card into receiver. Press [menu] Select [SD Memory] Note: Receiver will automatically create 3 directories on the card: CH Data Backup Code Backup MP3 (For Virgin cards only -Take the card out at this point and load your unzipped bin or channel list file to the card in the appropriate directory. Now put the card back in and re-access via menu as stated above.) Select bin file in appropriate directory, main directory, [ch data backup] or [code backup] Press [OK] Select [data restore] Press [OK] to load, receiver will automatically load, confirm, then reboot. TO SAVE DATA Insert SD/MMC card into receiver. Press [menu] Select [SD Memory] Select an appropriate directory, main directory, [ch data backup] or [code backup] by using [up or down arrows] and [OK] Press RED button in left bottom corner of remote. Name your file on the alphanumeric screen file by scrolling via [arrows] to next character and then pressing [OK] for each character or [del] to correct a character. To save selected name, press [OK] on the alphanumeric screen. Bin File will then write automatically to the correct directory. Size of files: CH = 352 kb Code = 768 kb Use GREEN button (beside the RED button) to delete selected and unwanted files. https://www.ecoustics.com/electronics/forum/home-video/224237.html |