Channel List and Setup for 110-119-121-118..pleaseeeeeeeee

 

Bronze Member
Username: Sshaniga

Post Number: 13
Registered: Oct-07
Hi,
I am using Pansat 3500 SD. I loaded v304 correctly, I am getting channels on 110/119/121 but I am not getting any channels on 118.
Can someone send me the settings and how to get back the channels on 118. I already did blind scan.
Also can we use channel list with the new bins , if so what kind of channel list. Does any one have channel list for 110-119-121-118.

Thanks
 

Platinum Member
Username: Nydas

Post Number: 13310
Registered: Jun-06
YOU MUST HAVE

1. A 30-33" DISH.

2. A SPECIAL LNB FOR 118,

CB2008A OR DIGIWAVE DGL1189s.


You probably have item 1 but not 2.
 

Bronze Member
Username: Sshaniga

Post Number: 14
Registered: Oct-07
Hi Nalin,
I have superdish which is pointing to 118 W , I used to get all the channels before I loaded V304. Now I dont get... am I missing something?
Thanks
 

Platinum Member
Username: Nydas

Post Number: 13314
Registered: Jun-06
Can you name a few channels you were getting on 118?
 

Bronze Member
Username: Sshaniga

Post Number: 17
Registered: Oct-07
I used to get Gemini (799), MaaTV (811) and many other indian channels on this..

here are my settings:
EchoStar 7
LNB Type dish-pro
LNB Local-Freq 11250
22KHz off
Disec 1.0 #1
Legacy SW None
Skew 0
TP
Positioner Setting disable
Sat Scan all

Blind Scan info
Satellite EchoStar 7
Degree 119.0W
LNB Config 11250
Symbol Range Full
Polarity All
Scan All

EchoStar 8/10
LNB Type dish pro
LNB Local-Freq 11250
22KHz off
Disec 1.0 #2
Legacy SW None
Skew 0
TP
Positioner Setting disable
Sat Scan all

Blind Scan info
Satellite EchoStar 8/10
Degree 110W
LNB Config 11250
Symbol Range Full
Polarity All
Scan All


Echo118
LNB Type Dish Pro
LNB Local-Freq 11250
22KHz off
Disec 1.0 #3
Legacy SW none
Skew -45
TP
Positioner Setting Disable
Sat Scan All

Blind Scan info
Satellite Echo118
Degree 118.0W
LNB Config 11250
Symbol Range Full
Polarity All
Scan All

Echo121 (9-13)
LNB Type dish pro
LNB Local-Freq 10750
22KHz off
Disec 1.0 #4
Legacy SW none
Skew -45
TP
Positioner Setting disable
Sat Scan All

Blind Scan info
Satellite Echo121
Degree 121.0W
LNB Config 10750
Symbol Range Full
Polarity All
Scan All
 

Platinum Member
Username: Nydas

Post Number: 13318
Registered: Jun-06
For scanning 118w, you need to use LNB Freq 10750 (low 9750).

Where you say you are scanning 121, you are probably scanning 129. You can't easily have 119 and 121 on one dish.

This would apply if you have 1000+, see file below.

application/mswordUpload
DP 1000+.doc (66.0 k)
 

Platinum Member
Username: Nydas

Post Number: 13319
Registered: Jun-06
If you are scanning without the special 118 kit installed, you probably have the slightly smaller dish and you were scaning 119 twice - once on 119 slate as 119 and then on the 118 or 121 slate as 118
If that is the case there is no separate output for the 118 on your LNB, and you will have to use the same DiseqC for the 118 slate as for 119.
118 slate always need LNB freq as 10750 or less and the first TP as 11715 or do a blind scan.
 

Bronze Member
Username: Jagsa

Post Number: 26
Registered: Dec-07
Hi Nalin,plymouth
I did a flash of a v302 and did a three times factory reset. loaded a latest 304Femu bin and did the reset of user and local channel setting
I am in Toronto and I could not find the same as the list has only US cities,nevertheless did a TP scanning and finally DiscQ settings as well. I sat scanned for Anik 3 and Echo 8.1 separately. I waited for almost an hour for each one of anik and 8.1 The signal quality and level are surprisingly at 89% and 90%,
STILL SCRAMBLED CHANNEL.

DO SOMETHING FOR THE MESS I AM IN PLEASE

Thanks
 

Platinum Member
Username: Nydas

Post Number: 13370
Registered: Jun-06
Delete all channels.
Scan just a few TPs and get the system going. Then scan the remaining on one sat.
After this sat is working, get the other sat going in the same way.
 

Bronze Member
Username: Jagsa

Post Number: 27
Registered: Dec-07
Thanks nalin
I will do so and get back in case?????
 

Bronze Member
Username: Jagsa

Post Number: 28
Registered: Dec-07
Well Nalin
I am back to square one

I did the individual TP scan , it went through alright but the only channels which I am getting are the BeV "For information only" channels only, no picture, and most of them show as scrambled channel.

Looks like gettting there but not quite, any more suggestions to get there, please inform.

Thanks again
 

Bronze Member
Username: Kakapapa

Post Number: 41
Registered: Sep-06
Nalin,

Where can buy dish 1000+ and switch.

thanks
 

Gold Member
Username: Plymouth

Canada

Post Number: 6016
Registered: Jan-08
Kaka
Buy a 33" and a Digiwave DGL1189s or CB2008A LNB.
 

Bronze Member
Username: Tooter

Post Number: 93
Registered: Oct-08
jags .. if you want dn channels you have to aim the dish to the dn sats..

you are receiving bev which will always show bad scrambled channel


www.dishpointer.com
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us