Panssat FLU......help needed?
|
New member Username: CanadiandudePost Number: 4 Registered: Jan-06 | I have convertef FLU.I flashed 252 jvvh bin yesterday.Originally all the channels were coming now only alpha punjabi and zee gujrati is coming for other channels it shows no signal? Why is so if the bin is down than even those two channels should not come ? |
|
New member Username: Lochness90Post Number: 6 Registered: Feb-08 | Try turn off the switch at the back for 3 secs then on |
|
New member Username: CanadiandudePost Number: 5 Registered: Jan-06 | tried that loch did not work? |
|
New member Username: CanadiandudePost Number: 6 Registered: Jan-06 | Nalin can you help me out? |
|
Silver Member Username: MetallicaPost Number: 179 Registered: Jan-08 | X Factor try to delete all those channels and do a blind scan again. |
|
New member Username: CanadiandudePost Number: 7 Registered: Jan-06 | metallica to delete the channels...wat shud i do....does i go for factory settings options? |
|
Silver Member Username: MetallicaPost Number: 180 Registered: Jan-08 | go to meanu...channel edit...go to delete..delete all channels.. after you have deleted all your channels...go to blind scan and rescan all your SAT again. |
|
New member Username: CanadiandudePost Number: 8 Registered: Jan-06 | thanks metallica,,,,i deleted the channels ..but now it is not picking signals at all....in the satallite set up..there are no signals |
|
Silver Member Username: MetallicaPost Number: 181 Registered: Jan-08 | X Factor...when you deleted all your channels like i told you to.. your satallite set up stay the same like b4..only when you do a factory settings than you have to reconfigure your SAT setting again... what SAT are you watching? |
|
New member Username: CanadiandudePost Number: 9 Registered: Jan-06 | i was getting my indian channels on 157 w with echo 4ku..now i cant scan echo 4ku as it shows no signals...the only file which is showing signals are nimiq..files |
|
Silver Member Username: MetallicaPost Number: 182 Registered: Jan-08 | on echo 4ku see if your SAT setting is right setting. see if your LNB is the right setting. and the Diseqc port is right setting. and if you check it all still no signal..just try to load the lastest bin again to see it work or not. |
|
New member Username: CanadiandudePost Number: 10 Registered: Jan-06 | sat settings are right....it scanned nimiq file and again only two channels are showing....alpha punjab and zee gujrati. and for some odd reasons not picking up signals for echo4ku |
|
New member Username: Lochness90Post Number: 8 Registered: Feb-08 | So when you do a blind scan, all correct channels came back, but only 2 with good signal? How strong is the signal? on good channel and bad channels? |
|
Gold Member Username: NydasPost Number: 8459 Registered: Jun-06 | First of all what is this 157W? It is not listed in Lyngssat You would be scanning the Sat you are pointing to physically irrespectively what you choose in the Antenna menu. Make sure you have these settings (available at Echo 1,2):- LNB type: Standard LNB Local Freq: 11250 22 khz off DisEqC switch: select the port where the Dish is connected to the switch if there is more than one LNB/Dish Legacy Switch : None skew 45 TP (1)12223 V 20000 (other TPs are in the Lyngsat list but don't matter much in a blind or a full scan With the above settings and pointing to 148W you should be able to get the channels. If you have Dishpro LNB - use that in your setup. If your Dish output is going through a Dish prop Plus, your switch setting should be 3 or 4, but it does complicate matters. |
|
New member Username: Hashbaba420Post Number: 1 Registered: Feb-08 | hi there can someone plz help me.. i have a clone pansat 3000 and its dead. no lights comes on when i turn it on, but i do hear a clicking noise when i turn it on. it is converted to pansat 2500. i usually put pansat 2500 bins and it worked fine. i put the wrong bin and i killed it. some one plz help!!!!  can i jtag it?? |
|
Gold Member Username: NydasPost Number: 8568 Registered: Jun-06 | Try serial method first. Try Revert to 2500 and then reconvert. If all fails, do a jtag. **-- **-- **-- **-- **-- **-- **-- **-- **-- **-- **-- The full kit is in full_kit253C.zip or later. Download and unzip in a new jvvh directory. Read the instructions in the Instructions.doc file. Also available separately in All_253.zip file with all the conversion 253 BINs released so far. http://public.box.net/2500_full_kit |
|
New member Username: Hashbaba420Post Number: 2 Registered: Feb-08 | thank u nalin nyda  I'll try it and see what happens.. |
Main Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics