|
New member Username: SunnydPost Number: 6 Registered: Jun-06 | ECHOSTAR KEYS N2 Updated: Tuesday, July 25 2006 at 4:39 PM -------------------------------------------------------------------------------- Dish Network: N 0101 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B N 0101 01: (active) 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC Key 86: Active: D1 15 0C 8E 66 82 D9 80 90 A9 20 20 37 07 87 08 Key 96: 93 B1 AA F1 4E 50 EB 94 A9 79 D7 6F 51 6A A3 92 Active |
|
Bronze Member Username: RikarddoPost Number: 51 Registered: Mar-06 | bs' this keys don't work |
|
Silver Member Username: Mybig_williePost Number: 105 Registered: Jul-06 | WTF.BS keys. |
|
Silver Member Username: Mybig_williePost Number: 107 Registered: Jul-06 | The DN keys are good but dont know what the others are. |
|
Gold Member Username: The_wank_artistPost Number: 1345 Registered: Feb-06 | The other keys are for BEV, and they are accurate. Thanks for posting them Aasim |
|
Bronze Member Username: HeroPost Number: 31 Registered: Jun-06 | so what works? LOL don't waste your time and energy |
|
New member Username: The_only_onePost Number: 4 Registered: Jul-06 | these keys are only for locals ... they work perfectly!!! thanks for sharing aasim! |
|
Bronze Member Username: JcanavatiPost Number: 56 Registered: May-06 | They do work for locals, thanks Aasim. |
|
Bronze Member Username: ArizaPost Number: 90 Registered: Feb-06 | give me keys for ariza700 damn you guys |
|
Bronze Member Username: TerryhhhPost Number: 29 Registered: Feb-06 | b#v?? still waiting for picture ten minutes?? did I do something wrong?? |
|
Silver Member Username: Bazuka2020Post Number: 255 Registered: Oct-05 | Goback to see the keys if they change turn the auto roll off, what receiver you have? |
|
Silver Member Username: NorthmanPost Number: 133 Registered: Mar-06 | The active keys are the top row: DN. line 0: 0F..C5..21..D1..B6..04..8E..9E 90..CC..D3..12..58..E4..B6..9B Ignore any other lines. |
|
Gold Member Username: The_wank_artistPost Number: 1355 Registered: Feb-06 | Jib, keys for ariza700 (and any other fta receiver) are posted above. The DN locals will come in and a few others but that's about it. BEV is out entirely. terry, see the message I wrote to Jib. BEV won't work. They were most likely posted because the keys were c/p'd from keymaster. |
|
Bronze Member Username: ArizaPost Number: 93 Registered: Feb-06 | okay im gonna try these "keys" and "C" my way our of here for 2 minutes |
|
Bronze Member Username: ArizaPost Number: 95 Registered: Feb-06 | okay i go into nagravision 2 and there's two lines on "00" and when i go to "01" there's another two lines so where do i insert this code on nagravision 2? "00" or "01" ??? |
|
Silver Member Username: Mybig_williePost Number: 120 Registered: Jul-06 | 00 |
|
Silver Member Username: WaydownPost Number: 186 Registered: Jun-06 | The active keys are the top row: DN. line 00: 0F..C5..21..D1..B6..04..8E..9E 90..CC..D3..12..58..E4..B6..9B |
|
Gold Member Username: The_wank_artistPost Number: 1359 Registered: Feb-06 | Put them here... 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B 01: (active) 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC If you only have room for 32 characters, use the active keys (01). |
|
Silver Member Username: Bazuka2020Post Number: 264 Registered: Oct-05 | 00 = 16 keys 8 on each line 01 = 16 keys 8 on each line I think only 00 changed so change the 00 and see come back if you have problems. What receiver you have? |
|
Silver Member Username: WaydownPost Number: 188 Registered: Jun-06 | co0lsat( push remote 8282) 10-0F C5 21 D1 B6 04 8E 9E 11-90 CC D3 12 58 E4 B6 9B (active) 20-71 9C 60 71 04 C1 39 AE 21-88 FF F0 5E D2 4C F3 FC |
|
Bronze Member Username: ArizaPost Number: 97 Registered: Feb-06 | khan i got it working for mine.. its not bad,,, get a few locals |
|
Silver Member Username: Bazuka2020Post Number: 268 Registered: Oct-05 | Something is better than nothing |
|
Bronze Member Username: ArizaPost Number: 99 Registered: Feb-06 | true |
|
Bronze Member Username: WardomanPost Number: 11 Registered: Jul-06 | sorry if this is a repeat of someone else, just posting what I know Bell ExpressVu (Last Update: 2006/07/26 14:00 EST) Key 0: D1 15 0C 8E 66 82 D9 80 90 A9 20 20 37 07 87 08 Key 1: 93 B1 AA F1 4E 50 EB 94 A9 79 D7 6F 51 6A A3 92 Active Echostar DishNetwork (Last Update: 2006/07/25 01:08 EST) Key 0: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B Active Key 1: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC these keys do work, I tried them on my viewsat platnium and locals works fine, tried them on a co@lsat same thing |
|
New member Username: Ebay26Post Number: 8 Registered: Jul-06 | thanks it works. |
|
Bronze Member Username: DailcePost Number: 18 Registered: May-06 | The BEV keys do not work! |
|
Bronze Member Username: M3stylzCalgary, Alberta Post Number: 26 Registered: Jun-06 | How did you guys get your DN keys to work? |
|
Silver Member Username: MinPost Number: 206 Registered: Jun-06 | I think the BEV almost all dead.that why....... |
|
New member Username: LovelyboybrPost Number: 1 Registered: Jul-06 | can someone here explain me how do i put those keys down on my viewsat platinum ? i already tried and theres always a missing number.. how many digits it gotta be? how it starts? hehe sorry im first time doing this by myself. |
|
Bronze Member Username: Hockeys_backPost Number: 18 Registered: Oct-05 | i can't get it to work. I have a pantec, and when i used to enter the keys it was only 32 characters, but after the last bin change i took my fta to some guy to make the change for me, and now i have 64 characters. This is what i am doing, for line 00: i am putting in 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B and for 01: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC and for the provider id i have 0101. Is there anything i did wrong?? |
|
Gold Member Username: The_wank_artistPost Number: 1382 Registered: Feb-06 | Hockey, Just double check the keys you're entering. If you wrote them down, make sure you wrote them down correctly. I didn't once and almost pulled my hair out trying to get them to work. You have the right order. 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B 01: (active) 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC If that doesn't work, just try entering the active line in both the 00 and 01. For your receiver that's all that matters. |
|
New member Username: Rik1Post Number: 5 Registered: May-06 | my reciever wont let me type in F (EPG) its a pansat 2500 |
|
Bronze Member Username: Hockeys_backPost Number: 20 Registered: Oct-05 | i tired that, and now when i go to nav2 in the key line it says FF and all the key numbers say FF FF FF FF FF etc.... so i try and change the ff to oo, and enter the keys, then save, then go back up change ff to 01 and enter the keys and save, but then nothing works. The when i go back to nav2 there's a 00 key line with the keys and a 01 key with the keys and a FF key line with keys FF FF...etc What the heck did i do? I have never had any problems before entering keys, it was so simple, and now for some reason i can't do it. |
|
Silver Member Username: JohnnerMiami, Florida Post Number: 383 Registered: Nov-05 | just set it to default keys and renter the keys |
|
Silver Member Username: MinPost Number: 209 Registered: Jun-06 | RIK,maybe your(EPG)button is mess up,try to press hurter,or take out the battery and put it back in to see what happen,because i don't see anybody have this problem before....goodluck..... |
|
New member Username: HarryoneRock Hill, SC USA Post Number: 1 Registered: Jun-06 | Way Down you are one cool dude. I have been combing the stunningly slow Al7*** web site looking for help, loaded faulty keys, wasn't sure even which lines went where (My first key change). Your answer re CS keys was IT. Boom! Locals back. It's a small thing but better than nothing. Thanks again! |
|
Bronze Member Username: Hockeys_backPost Number: 21 Registered: Oct-05 | alright, so i tried to enter provider id 0101 and keys 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B and 01: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC and nothing worked, then i changed the keys around in 00 i put keys 01 and in 01 i put keys 00, and then went back to the ch's and it says "wait for picture" and its at 510% and still going.... WTF??? |
|
Gold Member Username: The_wank_artistPost Number: 1384 Registered: Feb-06 | Go back to nag2. 0101 enter in 00 line: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC enter in 01 line: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC Those are the active keys, again, they are all that matter for you. Make sure you're saving them before you exit each screen. If it makes it more fun for you, we'll start a little drinking game. Eveytime you post back with no picture, eveyone has to take a shot. Don't get us too drunk, there are some freaks in this forum that might take advantage of us. |
|
New member Username: LovelyboybrPost Number: 2 Registered: Jul-06 | can someone here help me ? how can i put this key on my viewsat platinum. |
|
Bronze Member Username: Hockeys_backPost Number: 22 Registered: Oct-05 | dude, i think we are all going to get very drunk!! i tired that, and all i got was "wait for picture" and it goes from 100% to 900% and then back to 100% and over and over. So then i tired the other keys 00:0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B and 01:0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B and nothing. so what kind of shots should we do?? |
|
Gold Member Username: The_wank_artistPost Number: 1389 Registered: Feb-06 | press menu then - installation code is 0000 or 0937 then go to--code then go to- nagra at nagra Dish 01 01 00 08--0F C5 21 D1 B6 04 8E 9E 09--90 CC D3 12 58 E4 B6 9B 88--71 9C 60 71 04 C1 39 AE 89--88 FF F0 5E D2 4C F3 FC |
|
New member Username: LovelyboybrPost Number: 3 Registered: Jul-06 | please someone help me? with my vs? someone? please? |
|
Gold Member Username: The_wank_artistPost Number: 1390 Registered: Feb-06 | Hoceky, Pantec is the same as a Pansat so follow these instructions. And I'll take a shot of Crown Royal. If you say Peach Snapps I'm going to hunt you down and kill you. C/P from thill (you know who) For All Pansats -------------------------------------------------------------------------------- Press menu button on your remote: #1 Go to parental control... #2 Go down to "second pin" option & enter 0000 #3 Then go to nagravision and select it by pressing ok button on your remote... #4 In Nagravision window you should be in the box that is Entitled "Provider ID"...scroll to the right (press right arrow button on remote) until it switches to Dishnetwork (00 01) #5 Now In Nagravision window go down (press down arrow on remote) to the box that contains "00" entitled "Key Number" #6 While in the box (highlighted "Key Number") that contains "00", scroll to the right until you see nagravision 2 at the top left of your screen #7 While in Nagravision2 you should still be in "Key Number" box and the number in that same box should be "00"...this is for Key 00 #8 Scroll down (press down arrow on remote) to key data and enter the new supplied key for 00 (within this site is the key change for Nagravision2)..take note on how to enter letters in the lower portion of the screen (ex. letter E=FAV button on remote) #9 Once key is edited select OK button on your remote (OK-STORE confirmation blinks twice in lower right of screen) #10 go back to the "00" box and move one click to the right which should take you to "01"..this is to edit the "01" key #11 Follow Steps 8 & 9 above (this time enter key data for key 01 instead of 00) #12 Click exit and click ok or yes to save changes then exit all the way out and you should be watching tv |
|
Gold Member Username: The_wank_artistPost Number: 1391 Registered: Feb-06 | rafael, the post at 7:33 was for you. |
|
Bronze Member Username: Hockeys_backPost Number: 23 Registered: Oct-05 | This sucks, i've tired everything and nothing |
|
Silver Member Username: MinPost Number: 210 Registered: Jun-06 | HOCKEY. 1.try to turn off auto see what happen. 2.after u finish enter keys remember to press ok a few time to save the keys. 3.after all that is done,turn off your box from the back and turn it back on,it call reset it might help,goodluck bubby....... |
|
New member Username: LovelyboybrPost Number: 4 Registered: Jul-06 | Tyler Durden thanks man.. ok i put it dere. and what should i do now? it says on my tv i have no channels |
|
New member Username: TalelcaPost Number: 2 Registered: Jun-06 | hello i put the new keys in my fortec star life time ultra but nothing works . any one can help me thank you. |
|
Bronze Member Username: Hockeys_backPost Number: 24 Registered: Oct-05 | guess what?? still nothing |
|
Bronze Member Username: Hockeys_backPost Number: 25 Registered: Oct-05 | nothing nothing nothing |
|
Bronze Member Username: ZunnaPost Number: 35 Registered: Jun-06 | when will the indian channels come anyone know?? |
|
New member Username: AasomeLakewood, Colorado USA Post Number: 2 Registered: Jul-06 | Guys, on Neusat 6000 in the hotkey section under Nagravision there are 3 sets of #s under provider ID 2 sets of # under Index and 8sets of # under key. example below. Provider ID Index Key 1 00 00 00 00 00 00 00 00 00 00 00 00 2 00 00 01 00 00 00 00 00 00 00 00 00 how do you input 16 set of # on 1 line. Please help. Thanx!!!!!!!!!!! |
|
New member Username: Tml2006Post Number: 1 Registered: Jul-06 | I know you guys have been very helpful with instructions on how to input these keys, but I was wondering if anyone knows how to input these keys (for DN) with an Ariza Extreme reciever? If so, can i please get a step by step instruction, because i can't seem to find it anywhere on the net. Thanks very much in advance. |
|
Gold Member Username: The_wank_artistPost Number: 1395 Registered: Feb-06 | George, these are the instructions for the 700 which should be close to the extreme I think. How To Change N2 Keys Ariza 700. I'll dig around and find the ones for the Az Ex and post if these don't work. C/P from Thill 1) Press Menu 2) Scroll Down to Parental Control, Press Enter 3) Press "i" key on remote, then enter pin number "2004" 4) Scroll down to Set Default Key, Press Enter 5) Scroll up to Nagravision, Press Enter 6) Press VOL Right twice, you will see Dish Network 7) Press CH Down once, then VOL Right Twice, you will now see Nagravision 2 displayed top left You are now at the key 00, Press CH Down once so you can edit the Key Data 9) Enter your new keys (write down the old ones to be safe) 10) Press Ok to store, then repeat with key 01 11) Press exit until you get back to tv, all channels will be available |
|
Gold Member Username: The_wank_artistPost Number: 1396 Registered: Feb-06 | Hockey and rafael, Tell me you have good news? |
|
New member Username: LironPost Number: 5 Registered: Jul-06 | Tyler , i have tried the azaria 700 procedure. Could not get to the keys. Where can i get the same bin |
|
Bronze Member Username: OshaHamilton, Ontario Canada Post Number: 33 Registered: Jul-06 | Tyler plz help me i have viewsat enter in 00 line: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC enter in 01 line: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC is this right code for me |
|
Silver Member Username: Bazuka2020Post Number: 287 Registered: Oct-05 | cp - al7bar Setting Up Ariza 700 Receiver Flashing Receiver & Setting up to TV With the receiver off (back) plug into PC using a NULL MODEM CABLE. Turn on receiver & follow these instructions. A) With a NULL MODEM CABLE flash using Ariza 7xx loader v4.03 (radio app only or let the file self pick) and download the (ex.AA1-272 for the 700 or AA2-272 for the 750) bin. Wait until it says download completed. Turn off at the back and remove. B) Take the R6 Satellite Dish cable and thread it into the IF Input jack on the back of the 700 (Should be top middle on the back of the receiver). C) The next step depends on the cables you are using. 1) IF hooking up to TV by R6 cable than thread it into the TV out jack than to the cable jack on the back of your TV. 2) Using RCA cables just plug into proper locations on both the 700 and TV. 3) If using S- Video don't forget to hook up the audio cables. (Note: On some models of TV's if you use RCA or S-video cables, you may need to set TV to video to view the 700 receiver) Software Installation Setup Click Menu on the remote and pick English, enter Installation click on Antenna Setup click on Satellite now pick your Satellite's (see examples below) 91'w, 110'w 119'w set LNB on, LNB to standard, LNB Frequency to 11250 use the remote number pad to put it in if its not already there. Set DISEqC to Sat location on switch or until you have Signal strength coming in. Level yellow & quality green. Examples A & B Example A) Setting up just one Satellite 91'w (No DISEqC switch is needed) 1) Satellite pick Nimiq1/ku 91'w 2) LNB power on 3) LNB type Standard (see note below) 4) LNB Local Freq enter 11250 5) 22khz off 6) DISEqC set to off (If you are using a DISEqC switch make sure the settings on the setup match the cable on the switch. (Check level yellow & quality green) 7) Positioner setting Disable Now your ready to scan the Sat. Push the green button, now push the green button again. You should see a blue tile set Data off, FTA off, Networks On. When the Sat has been scan exit and enter Parental control, push the i button than 2004 from the remote. Set EMU to on and exit (with the 272 bin this might already be set to on). To set up EPG you have to set the time. Click Menu, user setup, time setup, GMT to -05:00 for EST, Set year, month, day & time exit. Example B) Setting up 2 Sats. For 91'w & 110'w with DISEqC switch with cables in sat1 and sat3 1) Satellite pick Nimiq1/ku 91'w 2) LNB power on 3) LNB type Standard (see note below) 4) LNB Local Freq enter 11250 5) 22khz off 6) DISEqC set to 1 (cable is in that spot on the switch) (Check level yellow & quality green). 7) Positioner setting Disable 8) Push small red button to ***** Now repeat step 1 to ***** next Sat 1) Satellite pick Echo 8.6ku 110'w 2) LNB power on 3) LNB type Standard 4) LNB Local Freq enter 11250 5) 22khz off 6) DISEqC set to 3 (cable is in that spot on the switch) (Check level yellow & quality green). 7) Positioner setting Disable 8) Push small red button to ***** (More than 2 Sats repeat steps 1 to 8 making adjustments where necessary) Once you have *****d your last Sat push the small green (scan) button on the remote. Then push the small red button (multi-Sat). You should now see all the Satellites that have been *****d. Pick the 1st Sat and press ok, a blue tile will come up. Set Data to OFF, set FTA Only to off, set Network to ON & Press ok. It is now scanning that sat. When you see programs found (ex. 385) exit it should take you back to the page that shows all the Sats you *****d. If not just go back into Antenna set up and press red button. Pick the next Sat & repeat these steps until all the sats have been scan. When the last Sat has been scan exit and enter Parental control, push the i button than 2004 from the remote. Set EMU to on and exit (272 bin already set to on. 273 and newer bins see note below for setting EMU). To set up EPG you have to set the time. Click Menu, user setup, time setup, GMT to -05:00 for EST, Set year, month, day & time exit. YOU should now be watching TV. Please note: Bins and LNB SETTINGS BINS If your using bin 273, 274, 275, 276 or newer bins go to parental control push the i button than 2004, go to EMU set keycode to on than set to on the sats you have Dn, bev. etc.... LNB SETTINGS Make sure to pick the proper LNB in LNB setting during the setup. Most common is Standard. Satfree91 |
|
Bronze Member Username: Hockeys_backPost Number: 26 Registered: Oct-05 | Tyler Durden i got nothing. I've tried everything you said and still nothing, keeps says "scrambled or bad channel" or "wait for picture" but the % keeps going up and up |
|
Gold Member Username: The_wank_artistPost Number: 1398 Registered: Feb-06 | Hockey, You there? Need some info. What bin do you have. Receiver is pansat 2700? Are your keys holding when you enter them? (I'm so drunk right now!!! You gotta get this going) |
|
Gold Member Username: The_wank_artistPost Number: 1400 Registered: Feb-06 | Liron, C/P from Bill. FOR DN go into the keys menu and delete all the keys except the 4 starting with 000101 these are the nag 2 keys you need there are some that start 000001 and these are nag1 keys which are not needed so use the green button on them to delete the suckers. there is also 248 empty keyslots ..them suckers are all loaded with just zeroes... delete all them suckers as well ...when you are done you will only have 4 key slots left and they will all start with 000101 now edit those keys by putting in the right key data aaaaaa bb xx xx xx xx xx xx xx xx aaaaaa is the provider (dishnet 000101) bb are the key slots (00, 10, 01, 11) xx the rest of the stuff on the line is the key data 00 is first half of key 0 10 is the second half of key 0 01 is the first half of key 1 11 is the second half of key 1 press ok twice to save and then press exit this is a trick i stumbled on back in february when everyone was down and i was watching superbowl... it doesn't really turn autoroll off but it seems to keep the receiver from thinking it needs to look for keys the way these units work is different than most other boxes, autoroll is off by default and only turns itself on when the video signal is lost due to a key change... then it rolls till it finds new keys and once pic is restored then autoroll turns itself off again. for some reason those nag1 keys in there force the box to grab the wrong keys and then it goes into the autoroll loop for ever. |
|
New member Username: Tml2006Post Number: 2 Registered: Jul-06 | ok, this may sound very stupid, but I am a noob when it comes to FTA. (I'm an old directv user) Where exactly, do i point my dish? (i told you it was stupid) I only have one dish (single lnb--old directv dish), and I live in toronto, canada. Do i point it south-west direction(samedirection as DirecTV?), or south-east? (for DN) Also, just to clarify, i pick the echostar 7 satellite on my reciever? PS...one more thing, since i am a newbie to this stuff, do i first have to connect my reciever to my PC, or does manually inputting the keys replace that step? BASICALLY< what i'm asking is for a reference of some sort, step-by step, how to set up my reciever to the very first time (I have an ariza extreme) Sorry for the long post, and I thank you very much in advance for your gracious help. |
|
Silver Member Username: Bazuka2020Post Number: 300 Registered: Oct-05 | Join al7bar you will get all your answers there, |
|
New member Username: Tml2006Post Number: 3 Registered: Jul-06 | what's that |
|
Silver Member Username: Bazuka2020Post Number: 303 Registered: Oct-05 | www*al7bar*tk |
|
New member Username: Tml2006Post Number: 4 Registered: Jul-06 | it doesn't work...(and yes i did replace the *'s with .'s. |
|
Bronze Member Username: Abdou91514 Post Number: 53 Registered: Jun-06 | ITS SEAMS THAT PEOPLE HAVING TROUBLE WITH NEW KEYS before entering keys Go to autoroll option turn off all autoroll press ok enter the new keys o1o1 its id provider for DN 0901its id provider bev blind scan for echo3 and nimiq you get only some local channels (me I get back tv5 and thers) no arab channel no bev |
|
Silver Member Username: Bazuka2020Post Number: 306 Registered: Oct-05 | It will work, at the moment the site is very busy people trying to get info on new bin, you will get in. or if you have time search this site. 1 sat direction |
|
New member Username: Tml2006Post Number: 5 Registered: Jul-06 | it says that the site is not found |
|
Bronze Member Username: Abdou91514 Post Number: 54 Registered: Jun-06 | George there is nobody here born with knowledge if you want to see information about how to pointe you dish go to www*lyngsat*com dont foget to replace *by (.) you get all answers |
|
Gold Member Username: The_wank_artistPost Number: 1402 Registered: Feb-06 | Where exactly, do i point my dish? (i told you it was stupid) point your dish toward the DN sat. 110 degrees. try this site for sat angles http://www.kusat.com/go.php?path=/install/look.php I only have one dish (single lnb--old directv dish), and I live in toronto, canada. dish/lnb are fine, see above for where to point. S/W by the way Do i point it south-west direction(samedirection as DirecTV?), or south-east? (for DN) yes Also, just to clarify, i pick the echostar 7 satellite on my reciever? no, pick 110. It has the most going on right now PS...one more thing, since i am a newbie to this stuff, do i first have to connect my reciever to my PC, or does manually inputting the keys replace that step? you may need to download to your receiver the firmware. You can get it from dsstester. The bin should come with loading instructions too BASICALLY< what i'm asking is for a reference of some sort, step-by step, how to set up my reciever to the very first time (I have an ariza extreme) |
|
New member Username: Tml2006Post Number: 6 Registered: Jul-06 | thanks guys, i really do appreciate your help. i'll try that stuff out, and if i have any problems, i know where to find you (hopefully it'll be smoooooth sailing, but i doubt it) |
|
Bronze Member Username: Abdou91514 Post Number: 55 Registered: Jun-06 | good luck george |
|
New member Username: Strikingleafs013Post Number: 1 Registered: Jul-06 | ONce i go to NAGRAVISION then i can either go to NagraVision-1 or NagraVision-2 and if i'm on nagravision-1, on the key number i can select either '00' or '01', the thing is, the bar to enter the KEY is only 16 characters. so on 00: xx xx xx xx xx xx xx xx on 01: xx xx xx xx xx xx xx xx now if i select nagravision-2 i have the same thing key number: 00 xx xx xx xx xx xx xx xx key number: 01 xx xx xx xx xx xx xx xx so how can i enter my keys? |
|
Gold Member Username: The_wank_artistPost Number: 1404 Registered: Feb-06 | prateek, nag 2. Just enter the active keys. George, Best of luck. |
|
New member Username: TweezakPost Number: 4 Registered: Jun-06 | Hockey, I think I may see your problem. I also tried the sequence of keys: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC in both the 00 and 01 slots. After that, I got no channels. Then I went back and tried this combo as suggested earlier on. As soon as I changed the 00 set of values, my local channels were back. 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B 01: (active) 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC But, I'm turning off the TV again because I have homework to do. I gotta say, this Summer without TV has been great for my grades and my grandkids are reading and playing outside a lot more. I guess there's a silver lining after all. Good luck! |
|
New member Username: Strikingleafs013Post Number: 2 Registered: Jul-06 | i've tried both keys in the NAG-2 but it doesnt seem to work, what IS the active key? too many people saying different things |
|
Gold Member Username: The_wank_artistPost Number: 1405 Registered: Feb-06 | As Tweezak posted above, the actives are found in the 01 line. Split them in two such as this.... 00: 71 9C 60 71 04 C1 39 AE 01: 88 FF F0 5E D2 4C F3 FC 32 into 16. |
|
New member Username: PancakeMississauga, On Canada Post Number: 1 Registered: Jun-06 | i have tried bev keys with my viewsat platinum,i can hear some channels voice only but no picture,can anybody help me why it is like that? thank you |
|
Bronze Member Username: M3stylzCalgary, Alberta Post Number: 27 Registered: Jun-06 | So i got to put all the codes in the 00: and 01: Usally i just put my code in the 01: but ill try it... |
|
Bronze Member Username: M3stylzCalgary, Alberta Post Number: 28 Registered: Jun-06 | Ok i got it you gota put the 00 and the 01! Thanks Tweezak |
|
Silver Member Username: GeekerPost Number: 176 Registered: Nov-04 | Your doing a very good job ( Tyler and Wali Khan ) i greatly appriciate some cooaperation from people like you and thank you for all the other people that dont bash newbies. Keep up the good work guys (and gals)! Annas Khan |
|
Bronze Member Username: WardomanPost Number: 12 Registered: Jul-06 | They changed the keys already, these are the newest ones, looks like they got a handle on this now, they are rolling keys like mad Satellite Encryption Keys Bell ExpressVu (Last Update: 2006/07/27 2:30 EST) Key 0: CC C7 81 F9 F8 44 75 57 E1 C1 6C FE 6B 2D 31 C9 Key 1: DA CA CD F0 C2 81 DC A2 63 24 D2 89 66 C9 B6 C9 Active Echostar DishNetwork (Last Update: 2006/07/25 01:08 EST) Key 0: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B Active Key 1: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC |
|
New member Username: PancakeMississauga, On Canada Post Number: 2 Registered: Jun-06 | these keys doesnot work with bev |
|
Bronze Member Username: WardomanPost Number: 13 Registered: Jul-06 | make sure you are trying it on 91 not 81 0900100 that is where you need them |
|
New member Username: Strikingleafs013Post Number: 3 Registered: Jul-06 | do the indian channels work yet? |
|
New member Username: AlvinChula vista, California San diego Post Number: 1 Registered: Jul-06 | DOES ANYONE KNOW THE KEY FOR LAVA 3200? |
|
Silver Member Username: Ong_tuPost Number: 126 Registered: Jun-06 | Use KeyRipper V2.0.zip to get latest keys. |
|
New member Username: Ronmcc02Post Number: 2 Registered: Jul-06 | Would someone help me out with putting the key code into the viewsat 2000? I haven't done it before. Also I noticed it has a serial port cable with it, But my computer doesn't have a serial port connection. Will I have to go back to a older computer or is their another way? Please help.... |
|
New member Username: SunnydPost Number: 7 Registered: Jun-06 | You will have to go back to the other computer, And thanks to everyone for the comments. |
|
Silver Member Username: Bazuka2020Post Number: 337 Registered: Oct-05 | What channels you are getting on nimiq 91??? |
|
Bronze Member Username: NewtosatPost Number: 27 Registered: Jun-06 | which local channels are working ? when i scan i get local channels for abc, abc, cbs for atlanta, denver and chicago... the only one that works is in atlanta. are tnt, tbs and so on considered local ? because i am not getting them |
|
Silver Member Username: Mybig_williePost Number: 195 Registered: Jul-06 | And you wont. |
|
Bronze Member Username: Skz720Post Number: 19 Registered: Dec-05 | I entered the keys into my Pansat 2700A and only a couple of channels are airing. The channels are boring channels though..so thats just a FYI for people. |
|
New member Username: The_cellSt.john, N/a Antigua Post Number: 1 Registered: Jul-06 | i have a 2700 pansat and the keys dont work |
|
New member Username: The_cellSt.john, N/a Antigua Post Number: 2 Registered: Jul-06 | can someone tell me how to manualy upload the keys |
|
New member Username: AlvarezPost Number: 8 Registered: Jul-06 | thanks guys I appreciate the keys |
|
New member Username: Ronmcc02Post Number: 3 Registered: Jul-06 | I MAY BE STARTING TO GET A FEEL FOR THESE KEYS WORK. BUT I AM STILL NOT SURE. wOULD SOME NICE PERSON HELP ME OUT . I WOULD LIKE A GUIDE LIKE THE GUY DID EALIER IN THE FORUM THAT EXPLAINED IN SOME DETAIL HOW TO GET THE MACHINE OPERATIONAL AND PUT IN THE KEYS. I KNOW I SOUND DUMB ON THIS AND thats BECAUSE I AM. I haven't set it up yet. Just bought about 2 weeks before the "big chill". Someone..........hhhhhhhhhhhhhhheeeeeeeellllllllppppppppp! |
|
New member Username: OviPost Number: 3 Registered: May-06 | hy guys i have a clone of pansat and i tried all those khey for bev and they are not working.If somebady knows what khey are working for bev please post here for me .thanks |
|
Bronze Member Username: JowharPost Number: 26 Registered: Jun-06 | I have clone of pansat I have the locals use these keys 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B N 0101 01: (active) 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC |
|
New member Username: 4agemister2Post Number: 1 Registered: Aug-06 | how do i put it into my neusat sp6000, help please.???? thank you in advance |
|
Silver Member Username: DjsmithCanada Post Number: 124 Registered: Jul-06 | DON'T YELL AT ME IF THEY DONT WORK ======================================================== Dishnet Keys Updated: Tuesday, August 1 2006 at 9:44 AM Key 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B Key 01: 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC Bev Keys Updated: Tuesday, August 1 2006 at 9:44 AM Key 00: CD C7 63 31 18 A8 4F 26 F1 7B EC 58 E5 00 EC A1 Key 01: 53 89 06 D0 EF 83 CA D6 44 13 05 E6 7E 59 45 01 Active ======================================================== Dishnet Keys Updated: 07-25-06 18:45:33 Key 00: 0FC521D1B6048E9E90CCD31258E4B69B Key 01: 719C607104C139AE88FFF05ED24CF3FC Bev Keys Updated: 07-27-06 19:33:42 Key 00: CC781F9F8447557E1C16CFE6B2D31C9 Key 01: ACACDF0C281DCA26324D28966C9B6C9 ======================================================== http://www.CyberDBS.com/keys/keysn2.html Dishnet Keys Updated: 2006-07-25 19:11:08 Key 00: 0FC521D1B6048E9E90CCD31258E4B69B Key 01: 719C607104C139AE88FFF05ED24CF3FC Bev Keys Updated: 2006-08-01 14:45:00 Key 00: 55D131F63B7991E659A5209877FAFDCD Key 01: 6A1B0BEE170CBCE50B821B07B13A26B3 ======================================================== -------------------------------------------------------------------------------- ECHOSTAR KEYS N2 Updated: Tuesday, August 1 2006 at 9:44 AM -------------------------------------------------------------------------------- Dish Network: N 0101 00: 0F C5 21 D1 B6 04 8E 9E 90 CC D3 12 58 E4 B6 9B N 0101 01: (active) 71 9C 60 71 04 C1 39 AE 88 FF F0 5E D2 4C F3 FC Bell ExpressVu Key 86: Active: CD C7 63 31 18 A8 4F 26 F1 7B EC 58 E5 00 EC A1 Key 96: 53 89 06 D0 EF 83 CA D6 44 13 05 E6 7E 59 45 01 Active |
|
Gold Member Username: Maple_leafPost Number: 1542 Registered: Apr-05 | N 0901 00 55D131F63B7991E659A5209877FAFDCD N 0901 01 6A1B0BEE170CBCE50B821B07B13A26B3 N 0101 00 0FC521D1B6048E9E90CCD31258E4B69B N 0101 01 719C607104C139AE88FFF05ED24CF3FC At least get them right if your going to post keys.!!!!!!!!!!!!! |
|
Silver Member Username: DjsmithCanada Post Number: 127 Registered: Jul-06 | May I ask what was wrong with the keys I posted from http://www.CyberDBS.com/keys/keysn2.html Dishnet Keys Updated: 2006-07-25 19:11:08 Key 00: 0FC521D1B6048E9E90CCD31258E4B69B Key 01: 719C607104C139AE88FFF05ED24CF3FC Bev Keys Updated: 2006-08-01 14:45:00 Key 00: 55D131F63B7991E659A5209877FAFDCD Key 01: 6A1B0BEE170CBCE50B821B07B13A26B3 other than I didn't put in N 0901 etc.....other than that they look the same as yours ! |
|
Gold Member Username: Maple_leafPost Number: 1543 Registered: Apr-05 | Bell ExpressVu Key 86: Active: CD C7 63 31 18 A8 4F 26 F1 7B EC 58 E5 00 EC A1 Key 96: 53 89 06 D0 EF 83 CA D6 44 13 05 E6 7E 59 45 01 Active WRONG keys |
|
New member Username: BjaunedPost Number: 3 Registered: Aug-06 | Are any of these good for viewsat platinum?? If so, how do I put them in? |
|
New member Username: Foolproof2kPost Number: 1 Registered: Aug-06 | I need some help when I enter in the code in Nagra. The BEV code is shorter than in my receiver I have a Viewsat Platinum 2000. The codes that you guys give have 8 meaning 16 alpha numeric digitsXX-XX-XX-XX-XX-XX-XX-XX My receiver asks for 9 meaing 18 alpha numeric digits instead of 8 xx-xx-xx-xx-xx-xx-xx-xx-xx I need to know if I have to put something in the remainder of this 2 digits or are you guys messing up on writing the codes. PLEASE HELP!! |