102 card question ?

Dan New member Username: Cucon1 Post Number: 1 Registered: Jul-06	Posted on Thursday, July 27, 2006 - 14:19 GMT Can I program or unlock a rom 102 DN card with a Mikobu III that was used for testing the HU card ?
dantetn Silver Member Username: Donnie1973 Post Number: 150 Registered: May-06	Posted on Thursday, July 27, 2006 - 15:22 GMT yes... if modified is what I hear.
Gavin Gold Member Username: Gavincumm New York USA Post Number: 1255 Registered: Feb-05	Posted on Friday, July 28, 2006 - 00:41 GMT what is with the pron?
John Smith Bronze Member Username: Shutdafucup Post Number: 13 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:00 GMT Mikobu III Gently lift pins 1 and 4 of the HC00 chip. Lift pin 10 on the 232 chip, if your board has a 233 chip then lift pin 1. Solder jumper from AT90S2313 pin 14 to HC00 pin 10. Solder jumper from AT90S2313 pin 18 to HC00 pin 4. Solder jumper from HC00 pin 8 to HC4053 pin 9 (the one to the left looking at front of loader). Solder jumper from HC00 pin 9 to HC04 pin 2. Solder jumper from HC00 pin 1 to HC74 pin 5 (located right above HC00). Solder 2.2k resistor or (trim pot not really needed) from card slot vcc to ground (c10 is close by). Install switch from 232 pin 10 (or 233 pin 1) to AT90S2313 pin 18 (on for flashing and off for unlocking.
dantetn Silver Member Username: Donnie1973 Post Number: 159 Registered: May-06	Posted on Friday, July 28, 2006 - 01:09 GMT what about a t911 programmer? loved the link there jack azz
John Smith Bronze Member Username: Shutdafucup Post Number: 14 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:24 GMT t911 image is to large to upload. If shrunk, you will not be able to see where to cut traces on circuit board
dantetn Silver Member Username: Donnie1973 Post Number: 160 Registered: May-06	Posted on Friday, July 28, 2006 - 01:25 GMT cool, where could i see it?
John Smith Bronze Member Username: Shutdafucup Post Number: 15 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:27 GMT I could email it to you. I get it from a pay site I belong to.
Dan New member Username: Cucon1 Post Number: 2 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:30 GMT WOW ! thanks so much for the info John... I am really amazed ... Again, thank you John.
dantetn Silver Member Username: Donnie1973 Post Number: 161 Registered: May-06	Posted on Friday, July 28, 2006 - 01:32 GMT ok, i may regret this...lol danteintn@yahoo.com thanks john
John Smith Bronze Member Username: Shutdafucup Post Number: 16 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:40 GMT No problem Dan.
dantetn Silver Member Username: Donnie1973 Post Number: 162 Registered: May-06	Posted on Friday, July 28, 2006 - 01:42 GMT U rock! Thanks a lot. Have been looking for this.
John Smith Bronze Member Username: Shutdafucup Post Number: 17 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:43 GMT Your welcome
popo grow Bronze Member Username: Popogrow Post Number: 14 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:51 GMT John can i use any box for the rom 102 card
John Smith Bronze Member Username: Shutdafucup Post Number: 18 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:54 GMT No you need either a coolsat FTA receiver or a jtagged dishnet receiver
popo grow Bronze Member Username: Popogrow Post Number: 15 Registered: Jul-06	Posted on Friday, July 28, 2006 - 01:59 GMT ok thanks so all the dtv receiver that we use to use with hu cards are not good any more
John Smith Bronze Member Username: Shutdafucup Post Number: 19 Registered: Jul-06	Posted on Friday, July 28, 2006 - 02:03 GMT That is correct.

« Previous Thread Next Thread »

Main Forums

Forum Help

Follow Us