I AM LOOKING FOR SUB ENCLOSURE BLUEPRINTS

Closed: New threads not accepted on this page
  Thread Last Poster Posts Last Post
Archive through July 01, 2003phillip stoll100
Closed: New threads not accepted on this page
 

Synder
I built the nicest box for 2 12"'s in the back of a ford explorer
 

corey johnston
If everyone had SUV's instead of pickups, this forum wouldnt exist
 

im lookin for blueprints to a ported sub box for 2 12" JLaudio w6's...please...
 

what's up peeps do anyone have a plan or a site that shows . designe for 4 rockford 12s 800 peak 400 rms. but im trying to put it in a 1990 honda Acord.
 

i'm looking for blueprints for a soundstream spl 160 (16inch sub) thanks for any help
 

i can design a box for any speaker, any cubic ft. Just let me know what the model of the speakers are and the area you have to work with, model of vehicle. 20$ email me if you are interested. You have to build yourself. Unless in salt lake city area. Cost more for me to build it for you. jeremybudd@attbi.com
 

Looking for a blueprint for a box for a 98 Dodge Ram 1500 Quad cab that will fit 2 - 10" sony explods under the rear seat. Thanks to anyone who can help. please email me at, thecoeys@horizonview.net
 

Anybody got the blueprints for a ported box for a 12" Splx 500w sub can't find any on the web.
 

I have a 15 l7 and was going to take the dimensions from kicker.com, push the bottom out a couple inches to make the front lean back at 60 degrees because i have a wrangler with the back seat and want the sound to hit the back glass not the tail gate, will the change in dimensions mess up the sound? Will some one give me blueprints/dimensions for a box that will hit the back glass. I have like a 3x3 foot place to put it so size isn't a prob
 

Does anybody have the blueprints for a box with four 12" subwoofers for a 1995 mercury tracer. If so email me at forpetesake2@cox.net.
 

Lokking for blue prints for two 12" JL subs in a 98 ext. cab chevy.
 

I am looking for some good dimensions on a single 10 in sub enclosure. it has a 400 watt cuspid sub i can email more specs but blueprints or just dimensions of the pieces of wood i should cut would help. any added knowledge would be great too.
 

my email is palmersigns@comcast.net
 

i am looking for subwoofer plans and or blueprints for sub enclosures. Like for 2 12 inch subs or 2 10 inch subs. i need them as soon as possible please thanx and have a great day and a better 2 morrow!!!!!
 

andrew
where can i find how to build a box for 1 mtx10" in my 96 z71 ext cab
 

I need blue prints for two 10" audiobahn subs...they are going into a 1985 chevy single cab. Pleas e-mail me if you have any. THANKS whshockey4@yahoo.com
 

Anonymous
I have 2 10" JL W6V2 that I want to put into a 1992 Ford Mustang LX. I am looking for blueprints for a custom fitting box. any help please email me at kaulu440@yahoo.com
 

Anonymous
I'm looking for dimensions for a custom fix subwoofer box to go unders the back seat of a 2002 silverado(ext. cab). Does someone know where I can get this at? It will be for two rockford 10" subs. Thanks. Can e-mail me here at xcpolarisman1@hotmail.com
 

Anonymous
I am looking for blueprints for two 8" jl Audio's if you have band-pass box that would be ideal but if not then i would like to see specs of a wood box with a port hole on the top of the box! if you know where to get a bandpass box for 8" cheap that is in good condition please e-mail me posted below! I have a 92' Escort with a medium size trunk that can fit a box that is approximently 4'FT length that would be ideal. e mail for all demensions of the trunk. Thank you!!

jarrierchun@aol.com
and (sometimes problems with first one)
nickoli0052003@yahoo.com
 

PLEAZE HELP.... i need blue prints for 2 15's volfenhag subs..

sean001134@aol.com
please
 

i need info on makin a box for 2 audiobahn 15in. subs. I want to put them in my trunk of a 1991 Honda Accord. If someone can help me on this that would be great. Thanks.
 

I was wondering if anyone could give me blueprints for a two 12" sub enclosure to go behind the rear seats in my 01' Wrangler. please email them to me at jwa8514@aol.com
thanks a lot.
 

Anyone got blueprint of 12" sub enclosure to go under the rear seat in 2002 Dodge Ram 1500 Quad Cab? Your help would greatly appreciated. Thank you.
 

I am looking for a box to go under the rear seat of my 2001 Chevy Ext cab for a kicker L7. Can anyone help me with the specs for this? thanks!
 

BoomBoom
I need the Blueprints for the double 18" Adamson B218 subwoofer, y want to make me a pair. Some one out there have any information?
 

J. Kings
Can anyone give me the blueprints for a two 12" sub enclosure (ported) to go inside the trunk of my 2001 ford mustang w/460 mach system. Also can you give me any ideas, should I take out the mach system to give me more space, or not?
 

i need info on makin a box for 2 alpine type R 12in. subs. I want to put them in my trunk of a 1995+ Honda Accord. I need blue prints tips anything that can help. Thanks. email me asap at filo_romeo_69@hotmail.com
 

steven pulley
i need measurements for a speaker enclosure which will be home to a pair of rockford fosgate 10"punch z series subs-i have a 1994 silverado ext.cab ,and i want to build it to fit underneath the back seat.does anyone know the proper measurements?
 

i need measurements for a speaker enclosure which will be home to a pair of rockford fosgate 10"punch z series subs-i have a 1994 silverado ext.cab ,and i want to build it to fit underneath the back seat.does anyone know the proper measurements?
 

I was wondering if anyone could e-mail me a blueprint for a speaker box for two 12" JBL's. This is going to be my first box and I don't know how to start. I have A Ford Explorer so the shape doesn't matter as long as it sounds good. Thanks in advance to anyone who responds.
 

Looking for a design idea for 4-12" Subs (Sony Xplod P5 series) 2 facing up and 2 facing to the back of the seats. With enough room to mount 2 Sony Xplod 1000W amps and 1 600W amp. For a Chevy S-10 Ext Cab 97-00.
 

i need some blueprints on ported single truck boxes. thanks
 

i have box designs for infinity reference 1220W..small box design for low power rated amp(i use the sub myself in my home theatre with 120w amp and the sound is phenomenal).....sealed enclosure....have designs for ported and bandpass as well but have not tried them yet(just bought the MDF today)...i have tried other 12 inch subs in this box and they all sound great, but the infinity produced the most earth shattering bass (ask my nieghbours) if interested send me an email
 

dumbazz
I need a box design to put four 10" audiobahn flame series drivers in/on my moped.

how would I wire up my 5000-watt amp to the itty-bitty battery that starts the moped? Will I need a radio too?

I'm tryin' to pick up chicks!
 

I NEED PRINTS FOR A TRIPLE 12" VENTED ENCLOSURE THAT WILL HOUSE 3 JL 12W6'S. THEY REQUIRE BETWEEN 1.5 AND 2.5 CU. FT. EACH. THE VEHICLE IS A 1996 IMPALA. IF ANYONE IS UP TO THE TASK LET ME KNOW. WWW.CROOKED_KIDD@HOTMAIL.COM
 

Need assistance with blueprints for a box to build for my 2000 mustang convertible. I would like to keep some space for carrying my bowling ball, other than that I can use the entire trunk if neccessary... I removed the mach 460 system and replaced all speakers, but now have no bass to to the cheap speaker pods ford builds... I need to build soemthing that will give me decent sound when the top is down. Can anyone help me out or send me infor on sites they saw with other 99-newer mustangs convertibles that have a custom sub enclosure in the trunck. Thanks for all your help.
 

Anonymous
I hav an 01 S-10 ext cab and i need a box for 2 10"s and im not worried bout it taking up the whole back area. I found a box on ebay but dont really wanna pay 120 for a box that i could make for 25. Thanks ( darkstarsk8res@bellsouth.net )
 

Anonymous
need measurements to build a sealed box w/the front angled for a 15" eclipse titanium subwoofer.spec say it needs 6.0 cubic feet.
THANKS
 

I am looking for a box or blueprints for two RFP-4412's. Right now i have a bandpass box but i am looking for something smaller and i am even thinking of splitting them up and putting them in the back corners of my 1996 Isuzu Rodeo for a more custom look. If you can help me or know of any sites e-mail me at ajkez_86@yahoo.com

Thanks
 

I am looking for blueprints for 2-10 inch speaker box.
 

************L@@K*******NEED SOME HELP! I want to open a sub box outlet store...does anyone know where i can buy sub box blue prints for specific cars and trucks? please help.....!

thanks,
Bill
 

Anonymous
I am looking for blueprints for 2-12 inch speaker boxes that are able to fit in to the trunk of a car. Need help fast!
 

I'm looking for the best dimension blue print for a pair of Pioneer TS-W254C 10" subs in the trunk of a Civic 2002 4dr sedan. Any help or direction would be greatly appreciated.
 

Anonymous
I am looking for plans for a box holding 2 10" subs under the back seat of a 1998 Chevy Silverado.
joebobjost@hotmail.com
 

Richard
Looking for blueprints for a single, down-firing 10 inch sub to fit under rear seat in '03 Chev ext cab p/u. Any one have any?
rm@nemw.com
 

can anyone get me some blueprints for a sealed box for 2 10" mtx subs? I wanna make some cuz I don't have the cash to buy one.... e-mail me if ya can help... THX
 

I'm Looking for a custom sub box that holds 12" woofers under the rear seat of a 2002 dodge quad cab. Can anyone help ?
 

I HAVE A 200 F-150 EXTENDED CAB AND I NEED TO FIND A BOX TO HOUSE 2 10' ALPINE TYPE-S SUBS...IF ANYONE KNOWS WHERE HIT ME UP ILL LEAVE MY E-MAIL ADDRESS...THANX ALOT
 

i got 1 solorbaric box for a 10 and a12 i aslo got 2 sealed single 12 boxes i must get out of the house so email me if you interested thank you beljosm@dunwoody.edu
 

Hey I need Blue Prints for a box that is 6cubic ft. of air space. For four 12inch dual voice coil SPL subs. They need 1.5 cubic ft of airspace each. I am looking for a simple rectangle box with all the subs facing up, and it needs to fit in a 93' Buick Century. Please Help!!
 

Anonymous
There are a lot of retarded people here!!! People actually need blueprints for a sealed box?? LOL. I can see if it was a complicated vented box, but sealed?? Go enroll in 6th grade math and you'll be set
 

i already have a box for my 2 pioneer 15" subs (400 watts), it came with them. there was no port or nothing just a sealed box. what i am after is a correct dimension for the subs for a new box and was wondering if i did need to port them or not, and what size and where should i put it? i have a 4 door crew cab nissan frontier and the box is in the back seat, so room is not an issue, please direct me or lead me in the right direction thanks!!!!!! could you help me with the figures and etc....,
 

i am looking for a place tha builds a custom subwoofer box.I need a box for three 12" kicker comp Vr for a 2004 chevy reg cab without having to give my center console and be able to lift it up/down LOOKING FOR ONE ASAP
 

I need to know the dimensions for fitting 2 10 inch solo barac's under the seat of a 1999 GMC Sierra Regular Cab Sport Bed, or a web site to get one from
 

I need Blue Prints for a SubSolutions TP2X enclosure. Or how it basically looks inside.
 

I have a 1997 Chevrolet Silverado Extended Cab and I have two 12" Rockford Fosgate RFP3212. And I was wondering if anybody had blue prints or knew where I could buy a box for the two 12s to go under the rear seat and fire straight out towards the front? Email me at Kawasaki5726@aol.com
 

Thee Internet Junklord
This is simple. Get a calculator.

Cubic feet = Length x Width x Height in inches divided by 1728.

You're concerned (obviously) with the internal dimensions of the box, don't count the thickness of the top, bottom, sides, center panel (if any), etc.

Example:

How many cubic feet is a sub box that measures 20" long, 16" tall, 12" deep?

20x16x12 = 3840

3840 / 1728 = 2.22 cubic feet

Sheesh, I slept through Geometry and I figured this out....


Angled boxes are easy to figure also. If you're that interested, I'll do a small web page. It's easier to explain with a picture.

Fiberglass and other enclosures that don't have flat sides are more interesting. A good example is a fiberglass box in a spare tire well. To figure the volume for them, I've converted the volumes of different sized containers (glasses, bottles, a 5 gallon bucket) into cubic feet. Then you just fill the beast up with water or sand using the containers and add all the cubic feet up to get a total. If you need to hit a specific size, say 2 cubic feet, just dump in the appropriate amount of water or sand, level it out, run some duct tape around the outside at the water line, then line up the bottom of your flat MDF baffle to that.

I always went with water, a lot cheaper and easier than sand. Fiberglass is waterproof when it drys thoroughly. Either way, you'll probably have to shop-vac it out when you're done.
 

bell from leyland
fu*k me man i need blue prints for asmany boxs as i can but you carnt find them any where can you? its a pain in the fcuking ar*e init man?
 

Can you help me with a design to put 4 12" fosgate hx2's 2001 series in a 2003 chevy trail blazer ext
 

I NEED ENCLOSURE SPECS FOR A 15" ROUND SOLOBARIC L7 TO BE PLACED IN TRUNK OF A 98 HONDA ACCORD
 

Hey,Does anyone out there have plans for a bandpass box to suit jl audio 10w3v2's?
 

If anyone is looking for custom fiberglass boxes for your vehicle, email me and i can send your a couple of pics of what i can do. I currently have a fiberglass box with 2 Audiobahn Ultra Excursion 12's 900W RMS and 1800W peak. Worth over $2000 will sell for $1500.
 

Anonymous
I am looking for blueprints for a 2002 dodge ram quad cab speaker box enclosure for 2-10's
 

Anonymous
I HAVE 2 15" VISONIK SUBS THAT NEED 3.4 CU FT PER CHAMBER ON A VENTED OR PORTED BOX I WAS HOPING ON BUILDING A BANDPASS BOX WOULD ANYONE HAVE ANY PLANS FOR THIS MASSIVE BOX IF SO E-MAIL ME AT JIMDAPIMP2004@AOL.COM THANKS!
 

motoman22
GIVE ME A COOKIE!

*post 165 and counting*
 

bah humbug
 

TURBODIESEL88
ANYONE KNOW OF A BOX DESIGNER FOR BANDPASS BOXES OR HORN LOADED BOXES
 

hey, i need blueprints, or help designing blueprints for 2 mtx t6158 15" subs that require 1.75 cu. ft. of airspace.....they will need to fit in the trunk area of a 1991 eagle talon....if anyone can help it will be appreciated e-mail at evanspears1@msn.com
 

Help please.....looking to build a sub box for my son who has been on my back, but I want to do it right. He has 2 Volfenhag 10" subs500W 250RMS Dual Voice can anybody help me out with a plan to put them both in 1 box.
 

looking for blueprints on 12" L7 single ported box please.
 

motoman22
Ermanno,

Honestly, you can usually pick up prefab hatchback boxes for under $50 and they work well for subs like Volfenhag. They're already carpeted and prewired...mucho easier.

Having a custom box is always better but Volfenhag does not publish their full driver specs so we can't even toy with numbers to figure out what they really need. Custom boxes won't help that sub, just get one that fits and make sure the woofers are mounted really well.

If you want to build it anwyay, just make sure that there are two chambers in the box, each about one cubic foot in volume, and make sure the box is air tight. It's never a bad idea to pick up a couple of bags of PolyFill stuffing at Walmart (in the craft section.) It's what you put in pillows but it helps kill resonance in the box. Just lightly stuff one pound of polyfill per cubic foot of airspace (one pound per side.)

Have fun
 

Anonymous
I am looking for dimensions on vented subwoofer box for 2 10" vega vega subwoofers. please e-mail me at cwynowsky@yahoo.com thanks
 

Anonymous
I have a 94' Chevrolet regular cab and need blueprints to fit 2 12" L5 solo barics in a vented box. my max dimensions are 56"w x 16"h x 10"d on the bottom and 8"d on the top.
Jon_Gud@hotmail.com
 

looking for blueprints to put into a 90 civic hatchback. Any ideas? Anything is better than what i've been able to get ahold of..
 

motoman22
GoLowEuro, you can fit pretty much anything in the hatch of an early '90s Civic! I've seen four 18" subs back there before (minus the back seat of course.)
 

I am looking for blueprints for the best way to build an enclosure for one, 12" maybe two ,12" cerwin vegas I need the measurements to get the best performance out one or both... also do they need to be ported or not?? Please Help ...Thanks Alot
 

Anonymous
i'm looking for spec's for a box to fit a 15-inch kicker impulse 8ohm, if you have could u please send them to seth__125@hotmail.com
 

i am looking for blueprints for 4 audiobahn 12s
 

Anonymous
i'm looking for the prints to a custom box for 2 Audiobahn 12" FlameQ subs to fit behind the bench seat of a 1995 GMC full size std. cab pickup. any input welcome@ mithrandir_77_2002@hotmail.com .
 

If anyones' from the southern ca area, Ill build custom boxes to exact specs stronger than any mass produced piece of trash complete with all blueprints. If anyone wants me to get them blueprits on any box, I'll do it for $5-30 depending on application. My boxes do NOT flex and gaurantee better spl. Email me for more info.
 

I am looking for blueprints or custom sub boxes for a 2003 dodge ram 1500 quad-cab. I have two infinity 12's that i want to put in and i can't find anything.

amolick@hotmail.com
 

HEY

I NEED TO BUILD A BOX FOR A 18" SUB AND IM NOT SURE WHAT THE DIMENSIONS SHOULD BE. COULD ANYONE HELP ME FIGURE THEM OUT.

thanks
 

I want to build a vented enclosure for 98 blazer w/ 3 10" mtx subs 4ohm thunder series aprox room in the back is 22"h 30"l 3'w
 

i need some help i have 2 1006t flame q subs and i wanna know something about a box 2 build for them
 

Hi. I'm looking for specs for a box that will fit under the back seat of a 1995 Chevy Siverado Ext-cab. I want the box to hold 2-12inch subs. And fit completely under so people can still sit back their with no problems. Please e-mail me at ven9693@hotmail.com.
 

can someone help me with my 18" sub box

mitch21602001@yahoo.com
 

no one is really helping anyone here
 

Looking for blueprints to audio system of a Dodge Ram 2500, 1998. Small speakers need to be replace.
ANY INFO HELPFUL
EMAIL:
smokinsam68@yahoo.com
Thanks, Joe
 

looking for info to build a box for 2 xs jensen 10s
 

i am looking for blueprints for a sub enclosure.. i have 2 audiobahn 15" dvcs that needs 1.4 cubic feet per speaker... i want each speaker to have its own air space..can anyone help me find some? I'd greatly appreciate any help!
Thanks
 

I have 2 12" clarion 500 watt speakers I want to put in the trunk of my 1988 mustang. If there is anybody that can help me with the proper specifications I would appreciate it.
 

TERMINATOR
NO ONE IS HELPING ANYONE HERE.WHAT A COMPLETE WASTE OF TIME AND SPACE.
 

Unregistered guest
What type of box do I need for 4 planet audio 10" subs.. in a ext. cab 97 ford f-150. Email me at kmx100@aol.com
 

New member
Username: Redskin

Post Number: 1
Registered: 12-2003
JPNwhy don't you go to www.planetaudiousa.com
where they list box sizes for all their subs in
all the popular loadings?
 

New member
Username: Treymeister2005

Post Number: 1
Registered: 12-2003
If anyone has any plans for a box holding an MTX amp and 2 or one 10" subs for a '94 Jeep Wrangler YJ e-mail me the plans
 

Unregistered guest
I dont know crap about speakers. i have (2) sony explod 12inch woofers in a box. the guy that made my box for my blazer hooked them up to one port. i didnt go back cause im not crazy about my bass. i have a 5 channel amp 1200w should i seperate the woofers to their own port. Somebody please help
 

New member
Username: Its_bacon12

Post Number: 24
Registered: 12-2003
wow you are all in dire need of glasswolf's advice.....but one thing
you should all do soem research on your subs/boxes etc. before asking then maybe you'll recieve help
look at me for instance, i figured out what volume i wanted, for what subs and what kind of box

i got a little help from glasswolf and look wher ei am, it's halfway done already and for 1/4 the price it would be to have customly made by a pro

btw if anyone says they cant do it, remember these words, i am only 16.....
already designed my box and ive done my research - maybe not to the extend i needed but i did and i got some sweet @ss deals and help


anyways, you guys should find out some information on what you need help on and instead of throwing your problem on the huge pile of problems already here, start your own thread...im sure you can all dot hat too
 

Anonymous
 
anybody know where i can get blue prints for a box for 1 12"sub in the back of a regualr cab 1988 chevy s-10 with the seat all the way back? mjbt38@bellsouth.net
 

Anonymous
 
anybody know where i can get blue prints for a box for 1 12"sub in the back of a regualr cab 1988 chevy s-10 with the seat all the way back? mjbt38@bellsouth.net
 

Unregistered guest
Can anyone help me with a blueprint for 2 10's down firing under the rear seat in a 99' chevy ext.cab?
 

Unregistered guest
Does anyone have plans or suggestions for a box for a 10" behind the back seat of a '99 Jeep TJ?
 

Unregistered guest
Does anyone have plans or dimensions for a box for a 10" Pioneer Speaker in the back of a 94 Ford Explorer?
 

Anonymous
 
all you guys are f***ing morons
does it look like anyone here is goning to help you
look at all the requests and the small amount of replies
who wants to do somebody elses work for them... noone!!!!!
 

New member
Username: Jbk

Post Number: 1
Registered: 02-2004
I Need Blueprints And/or picks on how to buld a sub box for a 94 ext cab chevy for two JL Audio 10W3
 

New member
Username: Timberjon

Post Number: 10
Registered: 02-2004
Yeesh people. You cant just Ask for or find blueprints for these subs. Go to the manufacturers website and look there, or request dimensions for a box from their tech support department.

If they dont have one, get rid of your subs..

OR, learn how to calculate the box volume yourself!! its not hard. your all big boys now.
read and study this article.
http://www.crutchfieldadvisor.com/S-eqX9av8fGYH/reviews/20030701/build_box.html? page=2
 

Unregistered guest
Looking for blueprints for a down firing sub box. I have a chevy suburban w three rows. I have measured the are and can fit 6 10's in a box. Just need a blueprint to go off of. Email me some designs please. undertai@hotmail.com

Subs are MTX RT10-04
 

Unregistered guest
IM WANTING TO SELL 2 12"VR KICKER COMP SUBS WITH A BANPASS BOX FOR ABOUT $300 IF ANY 1 IS INTERSTEN E MAIL ME WILL TRADE FOR 2 10"
 

New member
Username: Cepl5869

Jordan, Mn Us

Post Number: 1
Registered: Mar-04
i am looking for blueprints for a dual sub box in the back of my 2000 3door ext cab chev truck i have a single one but would like two
 

Unregistered guest
I'm looking for blueprints for a box to fit in a 95 chevy silverado ext cab. I heard 2 or 3 10s is all i could fit in it, under the seats. Please email me if anyone has any input.
 

Silver Member
Username: Its_bacon12

Post Number: 237
Registered: Dec-03
will someone kill or lock this thread?
 

Anonymous
 
lol no kiding, but these are the actual boxes that these subs (12W6's) are suposed to have make sure you have acrobat reader

http://www.jlaudio.com/subwoofers/pdfs/W6v2_MAN.pdf
 

Unregistered guest
Looking for blueprints for a custom enclosure for a 98 VW passat, I will be putting two 12" Audiobahn AW1206T in it. Please email me at nic949@cox.net if you have bluebrints for this or if you can make some for a coast.
 

Victor Guerra
Unregistered guest
I need the blueprints for Cerwin Vages bass horns
 

Unregistered guest
Does anyone have Blueprints for a 2004 Dodge Quad Cab for 2 10" Subs? Please help!!

jeffk@wtka.net
 

Unregistered guest
Hey can anyone design a box for 4 2003 kickercomp VR's for a 1994 mustang cobra?
 

New member
Username: Ent_jbdl

Coaticook, PQ Quebec Canada

Post Number: 1
Registered: Apr-04
I have a 2002 silverado ext cab i need blue print for a twin 12"sub box to fit under rear seat the box need to have 1cubic ft for each sub
Thank you
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us