Let's Try this again, sub(s) for a Hifonics BXi 1206D
|
New member Username: B_rad_nepPost Number: 4 Registered: Apr-07 | here are the specs for the amp Features: Brutus BXi 1206D 1-Channel Mono-Block Operation SUPER D-Class Ampllifier Topography Ultra-Fi MOSFET Outputs Illuminated Hifonics Logo PWM MOSFET EXVP (Exponential Vari-Power Supply) SPC Twin Turbo-Torroids with Simpatico Coil Design Remote Bass Control Included Balanced Line Inputs w/ Optional Hifonics MM-BLD-1 Gold RCA Line Ouputs - Permit Amplifier Daisy-Chaining 4-Gauge Power Connectors Fully Adjustable Accu Cross Crossovers Inlude: -24dB Subsonic Filter (Adjusts 15-50Hz) Phase Shift Adjustments (0 to +180 Degrees) 24dB Low-Pass Crossover (Adjusts 35 - 250 Hz) Bass Boost: Variable Bass Equalization (+18dB @ 45Hz) SPECIFICATIONS 450W x 1 @ 4 Ohm 900W x 1 @ 2 Ohm 1200W x 1 @ 1 Ohm S/N Ratio : >95dB THD & Noise : <0.08% Heat Sink Dimension : 11.41" x 2.63" x 10.39" LHW My budget is $300 and i'm either looking for one 15" sub or two 12" subs. i was thinking maybe a 15" Kicker L7 or a couple 12" alpines (perhaps type Rs). i want loudness mainly. any constructive criticism? |
|
Silver Member Username: Smoke05Tucson, Arizona U.S. Post Number: 290 Registered: Jan-07 | well with that amp i would do the alpine type r dual 4 ohm... expect people to tell you that that amp is overrated... i dont know about that... but i dont like the kicker L7... |
|
New member Username: B_rad_nepPost Number: 5 Registered: Apr-07 | is it possible for me to run 2 dual type r's to one mono amp? |
|
Silver Member Username: Skibum12189Cleveland Post Number: 435 Registered: Mar-06 | if you don't already have the amp, for like 20-30 bucks more you could get a 1606d which is probably pushin 1200 watts rms mayybe 1300, and you could hook up the two alpine r's (D4 - ithink swr1242's) with the gain down and they'd slam or those same subs on the 1206, dont get a L7 and yes, you could run two dual 4 ohm vc type r's to that amp perfectly, make sure you get dual 4 ohm if you get that amp though |
|
New member Username: B_rad_nepPost Number: 7 Registered: Apr-07 | well i already have the amp so if i decide to go with the two type r's, what would be a good setting for the sub sonic, bass eq, low pass, phase, and level so that i don't fry the amp? and should i wire the subs parallel? would that wire them down to a 2 ohm load? |
|
New member Username: B_rad_nepPost Number: 9 Registered: Apr-07 | and would this be a good box for the two subs... http://cgi.ebay.com/DUAL-TWO-12-SUB-SUBWOOFER-BOX-SLOT-PORTED-VENT-MDF_W0QQitemZ 300097973385QQihZ020QQcategoryZ14945QQrdZ1QQcmdZViewItem i'm putting this all into a 2000 Toyota Camry |
|
New member Username: B_rad_nepPost Number: 10 Registered: Apr-07 | bump |
|
Silver Member Username: ShadeMoxee, Wa U.S. Post Number: 196 Registered: Nov-06 | don't buy that box, have logan or mark build u one. i have that exact box with type r 12's and a hifonics2006d, just trust me, have someone make u a box. |
|
Silver Member Username: Smoke05Tucson, Arizona U.S. Post Number: 291 Registered: Jan-07 | no,no,no... you want to wire the 2 subs to a 1 ohm load http://www.rockfordfosgate.com/rftech/woofer_wizard.asp?submitted=true&woofer_qt y=2&woofer_imp=4 you connect all positives and all negatives... and for the box dont buy a prefab build one or have one build it for you... their are some vox builders in here and if you want to do it your self here is a page that will help with the desing: http://subwoofertools.com/forum/ported-box.asp |
|
Bronze Member Username: B_rad_nepPost Number: 11 Registered: Apr-07 | aight, well if i have some1 make me a box should i have them make it vented? |
|
Bronze Member Username: B_rad_nepPost Number: 12 Registered: Apr-07 | thanx guys. so the 2 pos from both voice coils on the 1st sub go to the one pos output on the amp and the 2 pos from both voice coils on the 2nd sub connect to a diff pos output and repeat with neg? or all pos connect to 1 pos output and all neg connect to 1 neg output? i just want to be perfectly clear |
|
Bronze Member Username: B_rad_nepPost Number: 15 Registered: Apr-07 | bump |
|
Silver Member Username: Smoke05Tucson, Arizona U.S. Post Number: 301 Registered: Jan-07 | just like this: and you can either do slot vented (part of the box) or tube vented (sealed boxwithe a pvc tube going inside). www.the12volt.com this page have some calculators you may be able to use. |
Main Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics