Amp overheating

 

New member
Username: Yfz_rcr_12

NC

Post Number: 5
Registered: Aug-08
Is it normal for an amp to get very warm? It's not to hot to touch, but it's very warm. If it isn't normal, what can cause this?
 

Silver Member
Username: Hittin1

Lake Charles, La. United States

Post Number: 928
Registered: May-07
yes it is common for you amp to get warm... very warm in fact. What amp are you refering to and what is it pushing?
 

Silver Member
Username: Hittin1

Lake Charles, La. United States

Post Number: 929
Registered: May-07
and where is it mounted?
 

Platinum Member
Username: Wingmanalive

A pic is worth 1000 posts!!

Post Number: 17723
Registered: Jun-06
Warm is gooood.





Upload is baaad.
 

New member
Username: Yfz_rcr_12

NC

Post Number: 6
Registered: Aug-08
well it's a clarion apx 1300 pushing a 13w7, but the amp is only temporary.
 

Silver Member
Username: Quirky

SA, Texas

Post Number: 301
Registered: Feb-07
http://caraudioclassifieds.org/index.php?topic=121.0

just stumbled across this, looks like a good buy for that W7.
 

Gold Member
Username: Nd4spd18

Northwest PA

Post Number: 8095
Registered: Jul-06
That is normal. Also some amps run hotter than others, and it's not bad if the heatsink is hot. It IS bad when the amp shuts off and is extremely hot.
 

Gold Member
Username: 420alldaylong

Post Number: 3794
Registered: Sep-06
clarion apx 1300

400x1 at 4ohm
300x1 at 2ohm

Your W713" can be wired to .75ohm or 3ohm.

Do you smell anything while bumping the sub.
 

Gold Member
Username: Nd4spd18

Northwest PA

Post Number: 8098
Registered: Jul-06
Hey good call joey. If thats wired to .75 you're gonna burn up that amp.
 

New member
Username: Yfz_rcr_12

NC

Post Number: 7
Registered: Aug-08
I have it wired in a series. Another thing i am concerned about is voltage drop. The voltage changes alot even when the car is running.
 

Gold Member
Username: Nd4spd18

Northwest PA

Post Number: 8102
Registered: Jul-06
Well the sub is wired right then, 3 ohms.



But if your voltage is dropping that much, it's HO alternator time no 2 ways about it. And a better battery would be good also.

And damn, if you're getting that much voltage drop with only a 400w amp you're really going to need a beefed up electrical for anything bigger.
 

New member
Username: Yfz_rcr_12

NC

Post Number: 8
Registered: Aug-08
Would the amp in the link above be a good amp to push my w7? Also, is it stable bridged at 3 ohms?
 

Silver Member
Username: Teamrevolution

ATLANTA, GA USA

Post Number: 325
Registered: May-07
I get my amps hot enough to cook an egg.

Amps have diffrent temps they can reach before they go into protect or fail.

Check your input voltage and your voltage drop to see if there are problems. If either is lacking you will run the amp hot. A bad ground can also cause it to heat up fast.

But when you run a amp SUPER hard for a long time they are going to get rather hot. Make sure you keep good air flow to them.
 

Gold Member
Username: The_image_dynamic

San Diego, California

Post Number: 4458
Registered: Dec-06
Agreed. Class A/B amps, like DLS for example, get especially hot because the push-pull design causes power (efficiency) loss and relies heavily on traditional heat dissipation. Most modern amps are built especially for high internal temps, and the components, circuit boards and glues are all far better at handling heat then even a few years ago. Also, most will ramp down (reduce power output) when the circuitry senses that the amp is nearing protect mode.

The key to having an amp that will last a long time is to have adequate airflow all around the chassis, even underneath. It also helps the amp fans to expel the hot air if there is cool air circulating around, and not equally hot trapped air that defeats the fan's purpose. It's a catch-22 because having your amps out in the open attracts thieves, but simple physics will tell you that heat producing components need fresh air to survive.
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us