CW600 does not have 118.7 in the transponder??? HELP PLEASE
|
Silver Member Username: Fortec16Post Number: 161 Registered: May-06 | I am installing the 118.7 to 33" dish with 121W already. I have the 119 on the transponder search but could not find the 118.7. I have to buy the universal LNB tomorrow and install and which way I have to move the dish from 121W? I have CW600s model - Please help. |
|
Silver Member Username: Fortec16Post Number: 162 Registered: May-06 | HELP |
|
Gold Member Username: NydasPost Number: 7007 Registered: Jun-06 | You move 2 degrees Eastwards. |
|
Silver Member Username: Fortec16Post Number: 165 Registered: May-06 | I have 121w with 33" dish. I want to move to 118.7 + 119 W. I have CW600s I went to the transponder and I can only see 119w but 118.7 is not there. I am going to buy the LNB tomorrow from FUTUNE Computers (Universal LNB - $20.00) |
|
Bronze Member Username: PizzaPost Number: 65 Registered: Nov-06 | it is $10.oo circular lnb you have to ask 118.7 if you want to know the address http://www.aa-e.com/ this is just info you have many choices |
|
Bronze Member Username: PizzaPost Number: 67 Registered: Nov-06 | universal (circular lnb 118.7 ) LNB 10600 or 10750 LNB LOW 9750 port # as your setup do blind scan if you miss any channels then check tp frequency add those missing tp |
|
New member Username: Adamof99Post Number: 6 Registered: Nov-07 | Is any body knows how to get 118.7 or 119 I have a low frequency dual output circular LNB (attached below) that I purchased from http://elitesat.ca/ for $34. Every time I try to point to 118 or 119 I end up pointing to 110W with signal quality of only 26 but no luck with 118.7 or 119 I don't know what is wrong? I have 33" dish and Captive Works 600s P receiver I tried with the following Antenna Settings: for 119w : Transponder = 1224/V/2000/5/6 LNB Freq = 11250 LNB type = Normal 22KHz = Auto Diseqc Number= LNB3 (i am using a switch on #3) Legacy SW = Off Motorised System = None For 118.7W : Transponder = 11728/H/2000/7/8 LNB Freq = 9750/10750 or 10750 LNB type = Normal 22KHz = Auto Diseqc Number= LNB3 (i am using a switch on #3) Legacy SW = Off Motorised System = None Is any body know what I should change here in this settings or maybe this LNB is faulty (they claim that you can get both 118 and 119 with this LNB)  Features * Polarization: Circular * Input Frequency: 11.70 - 12.75 GHz * LO Frequency: 10.75 GHz * Noise: 0.5 dB * Dual output} |
|
Bronze Member Username: PizzaPost Number: 69 Registered: Nov-06 | For 118.7W : LNB Freq = 10750 (10600) LNB Freq low = 9750 LNB type = universal 22KHz = Auto Diseqc Number= LNB3 (i am using a switch on #3) Legacy SW = Off Motorised System = None |
|
Gold Member Username: TapemanNew York City in-HD, NY Post Number: 2090 Registered: Oct-06 | Your LNB is Fine For 118.75 yo need Freq=11715 Pol=V S/R= 20,000 FEC=7/8 or auto LNB type=Standard= 9750 to 10750 i.e. LNB Freq L= 9750 LNB Freq H=10750 DISEqC switch= just be 100% sure correct port I would try first straight from LNB to Receiver Yo must do Blind scan 118 and 119 same pointing same LNB Just different settings blind scan should update correct settings |
|
New member Username: Adamof99Post Number: 7 Registered: Nov-07 | Thanks Do you know what is the Dish pointing position? right now i am getting 110 with an other small dish |
|
New member Username: Adamof99Post Number: 8 Registered: Nov-07 | I am getting a blinking signal between 0-24 can't get more than 24 signal quality. but still i am not sure if this is 118 or 119 |
|
Gold Member Username: TapemanNew York City in-HD, NY Post Number: 2092 Registered: Oct-06 | Remember 118 and 119 are same pointing 1-LNB Small dish won't get 118 Yo need Universal LNB with 30" If yo blind scan with above settings and still no luck Then yo need to point to 119 One tip to point to 118 by placing reg circular to get 119 then remove LNB and place with universal LNB followed by blind scan When yo get blinking signal it means Wrong settings or wrong LNB pointed satellie |
|
New member Username: Adamof99Post Number: 9 Registered: Nov-07 | Hi Tapeman: Now I am getting 110 with 88% signal quality, after I replaced the 118.7 LNB with a regular circular LNB to get 119, but still not able to point to 119 Is it that hard to get 119, I tried almost all directions to point to 119 and tried to twist the LNB but still NO LUCK with 119 Is it not the same LNB type for 119 as 110, I am getting 110 very easy (even with the small dish 18") but NOT 119 ANY TIPS OR SUGGESTIONS, HOW TO POINT TO 119 OR 118.7 *** need some help, please*** THANKS, |
|
Gold Member Username: TapemanNew York City in-HD, NY Post Number: 2094 Registered: Oct-06 | There are many tips and techniques to get 110/118/119 on one dish 2 LNBs Depending on what DISH, LNBs, BRACKET etc. The tips I'll provide can work for most cases Requirements: - 30" dish - Bracket to 2 hold LNBs plus 2 LNBs - 1-reg Circular plus one Universal Circular or Invacom LNB - Extra Circular LNB for test - One coaxial coupler - 1 DISEqC switch - Good crimps and coaxial cables - Sat finder and compas can be greatly helpful Procedure: - Start with 2 basic circular LNBs aiming for 110/119 - Proper aiming and skew techiques is a must i.e. use 2 Sats with no skew won't get yo 2 Sats get each individual sat 1-at a time with a coupler instead of DISEqC at first - Do the usual settings for 110/119 remember no DISEqC yet - If yo have succefully got both 110/119 continue to next step otherwise back to proper aiming and skew - It is time now to replace 119LNB with your new Circular LNB - 110 and 119 should still be there 118 settings Freq=11715 Pol=V S/R= 20,000 LNB type=Standard= 9750 to 10750 - Do blind scan - If blind scan gets yo doubles yo may have to enter each tp one at a time and do regular scan FEC=7/8 or auto It is now time to place DISEqC switch Make sure yo turn off receiver everytime yo change coax cables and or LNBs Remember 118/119 on one LNB (Universal) scanned together or individually 110 on a seperate circular LNB Total of 2 DISEqC ports not 3 Final settings should be something like this For 118.7W : Transponder = 11715/V/2000/7/8 LNB Freq = 9750/10750 or 10750 LNB type = Universal 22KHz = OFF Diseqc= 1 Legacy SW = Off Motorised System = None for 119w : Transponder = 12224/V/2000/5/6 LNB Freq = 11250 LNB type = Normal or Universal 22KHz = OFF Diseqc=1 Legacy SW = Off Motorised System = None for 110w : Transponder = 12224/V/2000/5/6 LNB Freq = 11250 LNB type = Normal or Universal 22KHz = OFF Diseqc=2 Legacy SW = Off Motorised System = None I did not proof read this if there is errors I'll correct it later BUT IT SHOULD WORK TO MOST USERS ON MOST RECEIVERS |
|
Gold Member Username: TapemanNew York City in-HD, NY Post Number: 2095 Registered: Oct-06 |  |
|
New member Username: Adamof99Post Number: 10 Registered: Nov-07 | Thanks a lot King for the info I am able to point to 110 and getting 88% signal quality, but still not able to point to 119 (right/left OR up/down) thanks |
|
Gold Member Username: TapemanNew York City in-HD, NY Post Number: 2100 Registered: Oct-06 | It is neither left nor right Your problem is most likely a skew 2 Sats you must turn dish Looking at the back of the dish yo turn clock wise if yo live on the east cost If yo live on the west cost looking from the back of dish yo turn counterclockwise How much to turn Yo must enter multiple sats and select your zip code on this site If yo have trouble understand my procedure List all your hardware Receiver type Number of LNBs Dish DISEqC etc. List everything When I say list don't give me paragraph list... Also create a new thread Technically yo are hijacking someone's request Forum Rules must be enforced https://www.ecoustics.com/bbs/forumrules.htm |
|
Bronze Member Username: Adamof99Post Number: 12 Registered: Nov-07 | Hey King: I posted a new thread under: POINTING TO 119 AND 118 Thanks, |
Main Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics