Anyone know anything about subs and amps?
|
New member Username: Splinter00Post Number: 1 Registered: May-06 | ok if you got some experience or anything with subs and amps e-mail me, i need help connecting my sub to amp and i need to find some info on them but i dont no where to look, ill let you know what the problem is,so if you wanna help me just give me a shout at base_ket_balldude@hotmail.com  |
|
New member Username: Splinter00Post Number: 2 Registered: May-06 | ok ill just give you guys an idea of what i got here and see if you can peice it all together.. Sub: Kicker Solobaric S10L5: Speaker Type: Passive Nominal (RMS) Output Power: 450 Watt Max (RMS) Output Power: 900 Watt Response Bandwidth: 24 - 100 Hz Sensitivity: 86 dB Additional Features: Dual voice coil Amp: Planet Audio VX400D CLASS D MonoBlock Power Amplifier Max Power (2 Ohms) 600W X 1 RMS Power (2 Ohms) 350W X 1 RMS Power (4 Ohms) 200W X 1 Signal-to-Noise Ratio:100 db Frequency Response: 25-250Hz what do i all need as in an amp kit and will these 2 work together? i got a sub box that says 2ohm output on the back, so i have to make my sub a 2ohm will that work with the sub? |
|
New member Username: Splinter00Post Number: 3 Registered: May-06 | will that work with the amp** |
|
Silver Member Username: CtmikeCt. Post Number: 576 Registered: Feb-06 | jordan, that amp will work with that sub, just wire it to a 2ohm load, but you will be underpowering that sub by about 100w. |
|
Silver Member Username: Van_manBoston, MA Post Number: 313 Registered: Mar-06 | What are the voice coils duel 2 or 4 ohm? |
|
New member Username: Splinter00Post Number: 4 Registered: May-06 | yeah, thats what i thought, but it will have to do for now, what would i need for an amp kit? and what size gauge of wire? |
|
New member Username: Splinter00Post Number: 5 Registered: May-06 | 4 ohm on the sub |
|
Silver Member Username: Van_manBoston, MA Post Number: 314 Registered: Mar-06 | 2 4ohm coils or 2 2ohm coils? |
|
Silver Member Username: Van_manBoston, MA Post Number: 315 Registered: Mar-06 | Never mind just look it up here http://www.crutchfieldadvisor.com/learningcenter/car/subwoofers_wiring.html?view =all |
|
New member Username: Splinter00Post Number: 6 Registered: May-06 | on the box it says: solobaric s10l5 dual 4ohm vc woofer so im not sure, but it sounds like 2 4ohm coils |
|
Silver Member Username: Van_manBoston, MA Post Number: 316 Registered: Mar-06 | Option 1 http://www.crutchfieldadvisor.com/learningcenter/car/subwoofers_wiring.html?subs =2&impedance=DVC4x2 |
|
New member Username: Splinter00Post Number: 7 Registered: May-06 | ok thanks, also what do you think about setting all the gains on the amp? should i get someone to do it, or i was reading that if you set them all around 3/4 full it will be ok? |
|
Silver Member Username: Van_manBoston, MA Post Number: 323 Registered: Mar-06 | turn gains all the way down,Turn your Hu volume to the max position you would normal blair it at. slowly turn up the gain until it starts to distort, back it off a hair and your set. Do not exceed your max volume level once you set it. you could risk ruining your amp, subs or speakers due to clipping. |
|
Bronze Member Username: Splinter00Post Number: 11 Registered: May-06 | ok, what are the "gains" exactly, on the side of the amp it all says: Input level: min-max subsonic: lowest 15 highest 40 input sensitivity with 2 options:100mv-2v or 2-8V bridged mode: slave or master Phase: 0 or 180 low pas 50 lowest, 150 highest bass boost 0-18db also theres a remote level controller what should i do with that? can someone point me in the right direction? |
Main Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics