|
Bronze Member Username: Night_mirageAmmanJordan Post Number: 100 Registered: Jan-06 | i bought yasterday kx1200.1 and two of cvr's 12" dvc 4ohm i would like to buy another one can kx1200.1 push three of them > thanks |
|
Silver Member Username: PelonaPost Number: 531 Registered: Dec-05 | yes but it can also be used for two cvrs |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 101 Registered: Jan-06 | okay but does kx1200 will do the same worke on three or less |
|
Silver Member Username: PelonaPost Number: 532 Registered: Dec-05 | i dont know about that. but i would stay with 2 cvrs so you can get them at full excursion and itll be easier to install. and i think the ohms wont be right if you use 3 cvrs. |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 102 Registered: Jan-06 | thanks Pelon i also think so . cause cvr is 400 RMS and kx1200 push @4ohm 300 w |
|
Platinum Member Username: GlasswolfWisteria, Lane USA Post Number: 11062 Registered: Dec-03 | ideally you'd run four dual 2-ohm coil CVRs on that amp. get 300 watts each at 1 ohm. |
|
Silver Member Username: PelonaPost Number: 535 Registered: Dec-05 | i dont know. all that ohms sh!t confuses me. |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 105 Registered: Jan-06 | GlassWolf i did'nt understand you would you give me more details . |
|
Gold Member Username: TjmutlowPost Number: 1462 Registered: Sep-05 | take 4 of the comp vrs dual 2ohms and wire them series/parallel see www.the12volt.com under woofer wiring for the diagram. |
|
New member Username: ThunderforceNetherlands Post Number: 4 Registered: Feb-06 | If you use 4 DVC 4ohm Cvrs youre KX1200.1 wil go up in smoke, it will see a 0,5ohm load with 4 or a 0,667ohm load with 3 subs. KX1200.1 smells very bad |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 110 Registered: Jan-06 | okay what about SX1250.1 can i wire three 4ohm on it |
|
Platinum Member Username: GlasswolfWisteria, Lane USA Post Number: 11093 Registered: Dec-03 | in straight parallel, three dual 4 ohm coil subs would be a .666 ohm load. the amp would shut down and go into protection mode. |
|
Gold Member Username: TjmutlowPost Number: 1470 Registered: Sep-05 | you can run 4 dual4 to a 2ohm load. and then run a zx series amp like the 1500.1 |
|
Gold Member Username: BestmankindLos Angeles, CA USA Post Number: 2396 Registered: Oct-05 | "in straight parallel, three dual 4 ohm coil subs would be a .666 ohm load. the amp would shut down and go into protection mode. " that whole statement just sounds freaky. |
|
Gold Member Username: B101Queen City, NC USA Post Number: 1081 Registered: Sep-05 | lol. Chad .666 isnt too bad; but will probrably fry the hell out of that kicker amp. He would have to use better equipment. Isnt that thing 2ohm stable? |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 117 Registered: Jan-06 | no its 1 ohm i will put just two 12" cvr 2ohm is that okay |
|
New member Username: ThunderforceNetherlands Post Number: 6 Registered: Feb-06 | if you want to play at 0.667 you could better take a modified MTX 1501D. if you link 2 of them at 16volt they give over 6000W of power |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 119 Registered: Jan-06 | Thamks Thunder but i just want kicker .. |
|
Anonymous | if you put 2 dual 2 ohm subs you will get 2ohm or a .5ohm load depending on how you wire it or if you put 2 dual 4 ohm subs you will get 1ohm or a 4ohm load depending on how you wire it! |
|
Silver Member Username: Night_mirageAmmanJordan Post Number: 120 Registered: Jan-06 | anonymous i will put 2 cvr dual 4ohm on sx1250.1 amp |