NEED TOPSAT GUIDE FOR SETTING

 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 33
Registered: Dec-05
Dear all expert,

Can any bu send me TOPSAT guide how to upgrade with new software/bin and how to connect with network.

Please send a guide how to make it work, I just bought new box.

Amir
akhan64@gmail.com
 

Bronze Member
Username: Kbox

Post Number: 99
Registered: Jul-09
Load USB with new file (unzip)
Facture default
Load STB with the USB
Network setting in auto
Set antennas & Scan channels
Enjoy your T.V
 

Silver Member
Username: Kbox

Post Number: 101
Registered: Jul-09
Found this to be a cure for some of the setup problems on thetopsat 5000, maybe others can chime in to help out.

The setup of a topsat5000 is suppose to be very simple.
If you have attempted this before and have channels on your box you need to do a factory default to remove the channels then proceed with the following guide.

1: load the newest file via usb using SW Update.

2: Allow the box to reset then go into the network section and turn the network to "Auto" from "not used".

3: scroll down to the "apply" button on the bottom of the network setup page and click it using the ok button the remote.

(now it should zero out your settings for a moment or so then in a minute or so they will repopulate!).

4: after your network area repopulates then exit and setup one of your satellites.

If you are using echostar 7 (119W) then use that satellite and set your lnb type.

If you have a DP or DP plus use the "Dishpro1" lnb setting.

If you are using a standard lnb like the ones found on a single 18" dish then use 11250

Then set your Diseqc switch setting.

Again if it's Dishpro or Dishpro Plus use Diseqc port 1 or A.


5: If you did the above correct you should have signal and quality and you should get the 119 West indication underneath the satellite setup box to the left. If that says 110 instead of 119 then you need to make changes to your Diseqc switch settings, change ports to get the 119 setting.

After you do get signal and the satellite indicator does say "119 west" you need to scroll to the bottom and click on the "Search" button

Then go to channel 200 and you should have CNN.

Try doing a "HARD BOOT", shutting off rear switch for a minute and then back on.

If you get video on 119, you can scan for 110 and 91 afterward.
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 35
Registered: Dec-05
Thanks a lot Xbox, I have installed as per your instruction. Its working.

Dear pls let me know these channels are working at your end on 118w. I am only intereted on following channels.

787 ZEETV
788 TVASA
789 SET
790 ZCINE
791 B4U
793 SETMX
794 AAJTK
797 SHARA
798 SAMAY

Thanks
Arbab
 

Silver Member
Username: Kbox

Post Number: 103
Registered: Jul-09
http://topsatfta.org/channels/#DishNetwork
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 37
Registered: Dec-05
Dear Kbox,

Any plan of adding new following channels;

787 ZEETV
788 TVASA
789 SET
790 ZCINE
791 B4U
793 SETMX
794 AAJTK
797 SHARA
798 SAMAY
 

Silver Member
Username: Kbox

Post Number: 104
Registered: Jul-09
it will take some time how long i dont know
 

Silver Member
Username: Kbox

Post Number: 105
Registered: Jul-09
ok look here http://www.ikstopsat.com/Dish/Topsat_Dish.html
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 38
Registered: Dec-05
Dear, above channel are already scanned by topsat, but selecting any of above channel say scrambled.
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 41
Registered: Dec-05
dear expert,

is someone can send me remote control setting for topsat receiver?

amir
 

Silver Member
Username: Kbox

Post Number: 120
Registered: Jul-09
Turn on TV
2. Press and hold the 'TV' key and 'OK' buttons at the same time for 5 seconds, then the remote devices buttons will blink in a cycling manner a few times. The 'TV' button will then remain on.
3. Press the Up Arrow until your TV goes off.
4. Press the 'OK' button to save
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 42
Registered: Dec-05
Thanks a lot I will try
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 43
Registered: Dec-05
I tried the same with my samsung tv. I presse ok button when tv goes off, but still it does take any action from remote.
 

Bronze Member
Username: Akhan64

Toronto, On Ca

Post Number: 44
Registered: Dec-05
sorry for typo mistake

I tried the same above instruction with my samsung tv. I had pressed ok button when tv went off, but still it does not take any action from remote.

amir
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us